720427

Stanley STDR5206 Manual

6
Zoom out
Zoom in
Previous page
1/12
Next page
6
ENGLISH
• Always wear eye protection. Any power tool can throw
foreign objects into your eyes and cause permanent eye
damage. ALWAYS wear safety goggles (not glasses) that
comply with ANSI safety standard Z87.1. Everyday
glasses have only impact resistant lenses. They ARE
NOT safety glasses
Warning! Glasses or goggles not in compliance
with ANSI Z87.1 could cause serious injury when
they break.
• Never use the drywall screwdriver to drive screws other
than drywall screws. The drywall screwdriver and the
screwdriver bits are designed specifically for driving
drywall screws.
• Only use screwdriver bits that are designed for use with
this tool.
• Always keep hands out of the path of the drywall screw.
Avoid awkward hand positions where a sudden slip could
cause your hand to move into the path of the saw blade.
• Make sure there are no nails or foreign objects in the
part of the workpiece to be cut or sanded.
• To avoid injury from accidental starting, always remove
the plug from the power source before installing or
removing a screwdriver bit or when adjusting the depth
control.
• Always check the wall area where screws will be driven
to be sure there are no hidden electrical wires in the
area.
• Never leave the Lock-on button ON. Before plugging the
tool into the power source, make sure the lock-on button
is OFF.
General Safety Warnings
Warning! Wear a dust mask that is designed to be
used when operating a power tool in a dusty
environment.
Warning! Dust that is created by power sanding,
sawing, grinding, drilling, and other construction
activities may contain chemicals that are known to
cause cancer, birth defects, or other genetic abnormalities.
These chemicals include:
• Lead from lead-based paints
• Crystalline silica from bricks, cement, and other masonry
products
• Arsenic and chromium from chemically treate lumber
The level of risk from exposure to these chemicals varies,
according to how often this type of work is performed. In
order to reduce exposure to these chemicals, work in a
well-ventilated area, and use approved safety equipment,
such as a dust mask that is specifically designed to filter out
microscopic particles.
Safety Extension Cord
Warning! Keep the extension cord clear of the
working area. Position the cord so it will not get
caught on the workpiece, tools or any other obstructions
while you are working with the power tool.
Make sure any extension cord used with this tool is in good
condition. When using an extension cord, be sure to use one
of heavy enough gauge to carry the current the tool will
draw. An undersized cord will cause a drop in line voltage
resulting in loss of power and overheating.
Be sure your extension cord is properly wired and in good
condition. Always replace a damaged extension cord or
have it repaired by a qualified electrician before using it.
Protect your extension cord from sharp objects, excessive
heat and damp or wet areas.
Use a separate electrical circuit for your power tools. This
circuit must not be less than 14 gauge wire and should be
protected with either a 15 A time delayed fuse or circuit
breaker. Before connecting the power tool to the power
source, make sure the switch is in the OFF position and the
power source is the same as indicated on the nameplate.
Running at lower voltage will damage the motor.
Contents
Carefully unpack the drywall screwdriver. Compare the
contents against the “Drywall screwdriver components” chart
below.
Assembly and Operating
Warning! To avoid fire or toxic reaction, never use
gasoline, naphtha, acetone, lacquer thinner or
similar highly volatile solvents to clean the tool.
Forward/Reverse switch (Fig. B)
The forward/reverse switch (4) is conveniently mounted in
front of the variable speed trigger switch (5). To make the
screwdriver rotate clockwise for driving screws, push the
forward/reverse switch (4) to the left. To make the
screwdriver rotate counter-clockwise to remove screws,
push the forward/reverse switch (4) to the right.
(Original instructions)
… 6 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Stanley STDR5206 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Stanley STDR5206 in the language / languages: English as an attachment in your email.

The manual is 0,33 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info