720783
7
Zoom out
Zoom in
Previous page
1/11
Next page
7
ENGLISH
Features (Fig. A)
1. Collet chuck
2. Collet nut
3. Shaft cover
4. Ventilation slots
5. Cable
6. Toggle switch
7. Grinding Wheel
8. Spindle
9. Spanner
10. Front handle
11. Primary handle
Operating Instructions
1. Power supply
The power tool supply must match the nameplate data.
2. Installing wheel (Fig. B)
Warning! Only use grinding wheels with
maximum safe operating speed rated at or
above 40m/s. Ensure the grinding wheel is
correctly mounted and tightened, run the tool at no-load
speed for 30 secondes in safe position before using. Stop
immediately if there is considerable vibration or other
defects are detected. Never use damaged grinding wheels
or rimous ones.
a. Mount the spanner (9) to the spindle (8) and loosen the
clamping nut (2) with another spanner.
b. Insert the grinding wheel (7) shaft into the collet chuck
(1) as far as it can go.
c. Tighten the collet chuck (1) securely by spanners.
d. The maximum recommended diameter of mounted
wheel is 25mm.
e. The maximum recommended mandrel length of
mounted wheel is 24.5mm.
3. Switching on and off
Warning! Make sure you can control the switch
freely and keep it off before plugging in.
a. ON: Shift switch (6) to “I”. (Fig. E).
b. OFF: Shift switch (6) to “O”. (Fig E).
c. Let the wheel reach full speed before grinding.
d. Once the safety brush worn, grinder turns off
automatically to avoid motor damage. Motor was
damaged.
e. After inspecting and installing an accessory, run the
power tool at maximum no-load speed for five minutes
before any work.
Standard Attachments
1. Collet
2. Two Spanners (17mm)
Be sure to check the attachments as it is subject to change
by areas and models.
Application
Warning! To reduce the risk of injury, electric shock
and damage to the tool, before any work check the
utility lines electricity, gas or water supply line are
hidden in the work area.
Warning! Firmly grasp primary hold part of tool and
side handle before starting.
Grinding Application
a. Optimum grinding results are achieved when the
grinding tool is moved uniformly back and forth with light
pressure.
b. Pressure that is too strong reduces the performance
capability of the tool and cause the grinding to exhaust
more quickly.
c. Be sure that the distance between the top of collet chuck
and bottom of the grinding wheel is less than 8mm and
between the top of collet chuck and top of grinding wheel
is less than 45mm to prevent vibration of the tool and
unexpected accidents.(Fig. D)
Warning! Sparks generated when grinding
metal.Take care that no combustible material
presented on the area of flying sparks.
(Original instructions)
7


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Stanley STDG5006 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Stanley STDG5006 in the language / languages: English as an attachment in your email.

The manual is 3,77 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info