720472
7
Zoom out
Zoom in
Previous page
1/13
Next page
7
Do not attempt to charge damaged batteries.
Chargers
Use your STANLEY charger only to charge the battery in
the tool with which it was supplied. Other batteries could
burst, causing personal injury and damage.
Never attempt to charge non-rechargeable batteries.
Have defective cords replaced immediately.
Do not expose the charger to water.
Do not open the charger.
Do not probe the charger.
The charger is intended for indoor use only.
Read the instruction manual before use.
Electrical safety
Your charger is double insulated; therefore no
earth wire is required. Always check that the
mains voltage corresponds to the voltage on the
rating plate. Never attempt to replace the charger unit with a
regular mains plug.
If the supply cord is damaged, it must be replaced by the
manufacturer or an authorised STANLEY Service Centre
in order to avoid a hazard.
Features
This tool includes some or all of the following features.
1. Variable speed switch
2. Forward/reverse slider
3. Chuck
4. Torque adjustment collar
5. Battery
6. LED work light
7. Speed selector
8. Magnetic bit holder
FIG. A
9. Charger
10. Charging indicator
Assembly
Warning! Before assembly, remove the battery from the tool.
Fitting and removing the battry (FIG. C)
To fit the battery (5), line it up with the receptacle on the
tool. Slide the battery into the receptacle and push until
the battery snaps into place.
To remove the battery, push the release buttons (12)
while at the same time pulling the battery out of the
receptacle.
Fitting and removing a drill bit or screwdriver
bit (FIG. D)
This tool is fitted with a keyless chuck to allow for an easy
exchange of bits.
Lock the tool by setting the forward/reverse slider (2) to
the centre position.
Grasp the chuck (3) and rotate it in the counterclockwise
direction, as viewed from the chuck end.
Insert the bit shaft (13) into the chuck.
Firmly tighten the chuck by rotating it in the clockwise
direction as viewed from the chuck end.
Warning! Do not attempt to tighten drill bits (or any other
accessory) by gripping the front part of the chuck and turning
the tool on. Damage to the chuck and personal injury may
occur when changing accessories in this manner.
Use
Warning! Let the tool work at its own pace. Do not overload.
Charging the battery (FIG. A)
The battery needs to be charged before first use and
whenver it fails to produce sufficient power on jobs that were
easliy done before. The battery may become warm while
charging; this is normal and does not indicate a problem.
Warning! Do not charge the battery at ambient temperatures
below 10 °C or above 40 °C. Recommended charging
temperature: approx. 24 °C.
Note: The charger will not charge a battery if the cell
temperature is below approximately 10 °C or above 40
°C. The battery should be left in the charger and the
charger will begin to charge automatically when the cell
temperature warms up or cools down.
To charge the battery (5), insert it into the charger (10).
The battery wii only fit into the charger in one way. Do
not force.. Be sure that the battery is fully seated in the
charger.
Plug in the charger and switch on at the mains.
(Original instructions) ENGLISH
7


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Stanley STCD1081B2 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Stanley STCD1081B2 in the language / languages: English as an attachment in your email.

The manual is 1,55 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info