Manual Stanley ST-52-241-E (page 124 of 137) (English, German, Dutch, French, Polish, Portuguese, Spanish)

720234

124

Zoom out

Zoom in

1/137

NEVER LEAVE HEATER UNATTENDED WHILE CONNECTED TO A POWER SOURCE

Assembly (See Page 5)

1. Align holes in heater leg frame with lower

inner bracket.

2. Attach lower outer bracket to lower inner

bracket using screws.

3. Align lower inner bracket with side support.

4. Attach side supports to heater using tilt

adjustment knob.

5. Slide side supports into upper brackets, align

holes and insert screws to tighten.

6. Slide upper handle brackets onto front

handle, align holes and insert screws to

tighten.

7. Slide rear handle into upper handle brackets,

align holes and insert screws to tighten.

Operation

1. Position the fan heater so that it stands

upright on a firm, level surface and at a

safe distance from wet environments and

flammable objects.

2. Connect the fan heater to the proper electrical

power.

3. Set the thermostat dial to the maximum

temperature.

4. The fan heater will switch on when the

function selector dial is set to one of the

power settings.

5. Once the room reaches the desired

temperature, turn the thermostat dial back

until heating element turns off.

Automatic Overheat Safety Control

– This heater is equipped with safety internal

heat limiting thermostat and overheat

protection circuit. When a potential overheat

temperature is reached, the system will

automatically shut the heater off.

Thermostat Instructions

– At first, set the thermostat to “+” and let the

heater operate with full power input. When

the room temperature reaches the required

value, turn the thermostat to the left until it

switches off.

– The thermostat will then switch on and off

automatically to control the room temperature

according to the preset value and keep the

room temperature constant.

– When using the heater for the first time, you

may notice a slight emission of smoke. This

is quite normal and it stops after a short

time. The heating element is made of steel

and was coated with a layer of protective oil

during production. The smoke is caused by

the leftover oil as it is heated.

Cleaning and Maintenance

– Before cleaning the appliance, disconnect it

from the outlet and let it cool down.

– The enclosure is easy to get dirty. Wipe it

often with a soft sponge. For very dirty parts,

wipe with a sponge dipped in < 50°C water

and mild detergent, then dry the heater

enclosure with a clean cloth. Be careful not to

let the water enter the inside of the appliance

– In order to protect the enclosure, don’t

splash water onto the heater, and never

use a solvent like gasoline, isoamyl acetate,

toluene, etc. to clean the heater.

– When you store the heater, let it cool down

first and, keep it dry. Then cover it with a

plastic bag, put it in the packing box and

store it in a dry, ventilated place.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Stanley ST-52-241-E in the language / languages: English, German, Dutch, French, Polish, Portuguese, Spanish as an attachment in your email.

The manual is 16,35 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Stanley ST-52-241-E Manual

Product: