Manual Stanley ST-125T-KFA-E (page 78 of 85) (English, German, Dutch, French, Polish, Portuguese, Spanish)

720272

Zoom out

Zoom in

1/85

1030 Brussels, Belgium

NEVER LEAVE HEATER UNATTENDED WHILE CONNECTED TO A POWER SOURCE

Operation

This heater is factory-tested for use with 1-K kerosene/paraffin,

no. 1 & no. 2 diesel, JP8/Jet A Fuel, and no. 1 & no. 2 fuel oil.

TO START THE HEATER:

1. Fill the tank with paraffin until fuel gauge points to “F”.

2. Be sure fuel cap is secure.

3. Plug power cord into electrical outlet.

4. Turn thermostat control knob to desired temperature setting

(70/125/175/215 only). The setting range is from 5

C to 45

C. Push the Power switch to the “ON” position. The power

indicator lamp and room temperature display (125/175/215

only) will light and the heater will start.

Optimum pressure occurs when the nose cone is cherry red

and there are no extending flames from the heater.

NOTE: The room temperature display (125/175/215 only) will

indicate the following:

- When temperature is less than -17

C, display says “LO”.

- When temperature is above 37

C, display says “HI”.

- Between -17

and 37

C display shows actual temperature.

TO STOP THE HEATER: Turn the Temp. Setting Knob to left,

turn the Power Switch to “OFF” position, and unplug the Power

Cord.

TO RESTART THE HEATER

1. Wait ten seconds after shutting off heater.

2. Turn the Power Switch to “ON” position.

3. Be sure to follow all starting procedure precautions.

LONG TERM STORAGE

Drain Fuel Tank

1. For models ST-45/70T-KFA-E, drain fuel through the

fuel cap opening using an approved siphon. For models

ST-125/175/215-KFA-E, drain fuel through the Drain Plug at

the bottom of the Fuel Tank.

2. To remove the Drain Plug (125/175/215), pull the Plug Grip

downward and remove seal head from drain hole in tank.

3. Rinse and completely empty the tank.

4. To replace, push the drain head fully into the drain hole and

secure by pushing the seal cap fully into the head hole.

IMPORTANT: Never store leftover fuel over the summer.

Using old fuel can damage your heater.

Store heater in a dry, well-ventilated area! If your heater

cannot be stored indoors, a tarp or weatherproof cover must be

used to protect the heater.

Be sure that the storage area is free of dust and corrosive

vapors. Repack the heater in the original shipping material. Keep

the Users Manual in an easily accessible place.

Maintenance

Always service heater in a clean, flat, dry area. Never service

heater while it is plugged in or while hot!

Never service heater in wet conditions. In an emergency, be

sure heater has completely cooled before servicing using a

tarp or weatherproof cover, to ensure heater or electronics

inside heater are not exposed to wet conditions. Do not

service heater while plugged in under any circumstance.

FUEL/FUEL TANK: Flush every 200 hours of operation or as

needed with paraffin.

AIR FILTERS: Open heater lid to access filters. Filters should

be replaced every 500 hours of operation, or less, depending on

conditions. See figure 7.1 on page 7 for detailed view.

FAN BLADES: Open heater lid to access fan blades. Blades

should be cleaned at least once per heating season. See figure

6.1 on page 7 for detailed view.

NOZZLES: Open heater lid and remove burner head to access

nozzle. Nozzles should be cleaned or replaced at least once per

heating season. See figure 3.1 on page 7 for detailed view.

SPARK PLUG: Open heater lid to access spark plug. Clean and

re-gap every 600 hours of operation, or replace as needed.

Re-gap the terminals to 3.5mm. See figure 3.1 on page 7 for

detailed view.

PHOTOCELL: Open heater lid to access photocell. The Photocell

should be cleaned at least once per heating season or more

depending on conditions. See figures 4.1 and 5.1 on page 7 for

detailed view.

After servicing your heater you should perform the following

function check before commissioning this heater:

- check the air and fuel lines for leaks using a 50/50 soap

solution

- check extension cord for wear, cracks or cuts

- check to see igniter lines are connected securely to spark plug

Improper maintenance can lead to poor combustion and

soot production. Never alter or modify the heater. Use

only genuine parts from the manufacturer or sales agent

for repair and maintenance on your heater, and contact the

manufacturer or sales agent before replacing parts other

than those specified or recommended.

PUMP PRESSURE ADJUSTMENT:

While heater is operating, turn relief valve clockwise to increase,

counterclockwise to decrease. Use flat blade screwdriver to turn

valve. Correct pump pressure is on page 2.

This appliance is not intended for use by persons

(including children) with reduced physical, sensory or

mental capabilities, or lack of experience and

knowledge, unless they have been given supervision

or instruction concerning use of the appliance by a

person responsible for their safety. Children should

be supervised to ensure that they do not play with the

appliance.

If the power cord is damaged, it must be replaced by

the manufacturer, its service agent or similarly

qualified persons in order to avoid a hazard.

Figure 2. Start The Heater

On / Off Switch

LED Operating

Time/ Temp

Temp Setting Knob

LED - Fuel Gauge

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Stanley ST-125T-KFA-E in the language / languages: English, German, Dutch, French, Polish, Portuguese, Spanish as an attachment in your email.

The manual is 19,8 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Stanley ST-125T-KFA-E Manual

Product: