Manual Stanley ST-11T-CPH-E (page 3 of 6) (English)

720813

Zoom out

Zoom in

1/6

NEVER LEAVE HEATER UNATTENDED WHILE CONNECTED TO A POWER SOURCE

Bd. Général Wahis, 53, 1030 Brussels, Belgium

Connecting to Gas Supply

IMPORTANT! This heater requires a hose & regulator which are

defined in the instruction. Avoid twisting the hose.

1. To connect fuel cylinder, insert regulator end fitting into cylin-

der valve, rotate coupling nut clockwise and tighten.

2. Open valve on fuel cylinder slowly. If the valve is not opened

slowly, the excess flow check valve in the

regulator will stop the flow of gas. If this should happen, close

the valve, wait one minute and re-open, slowly.

VENTILATION

Always provide a fresh air opening in the heated space a mini-

mum of 25 cm

per kW of heat input (Hs), subject to a minimum

of 50 cm

, equally divided between high and low level. Provide a

larger opening if more heaters are being used.

The fuel pressure regulator and hose

assembly supplied with the heater

must be used without alteration (when

supplied).

Installation

1. Inspect fuel cylinder and hose connection to appliance to

ensure it is in good condition.

2. Connect regulator to a gas supply cylinder.

NOTE: Optimum efficiency is achieved when the heater uses

the appropriate full fuel cylinder

3. Slowly open the fuel cylinder. Leak test all gas connections

with 50/50 soap and water solution prior to start-up. Soap bub-

bles indicate a gas leak. DO NOT use a match or flame to test

for gas leaks.

Adjustment

Use only with the appropriate gases at the pressures listed on

the gas chart (page 4). This appliance is operating correctly when

the burners remain lit and glowing.

Lighting and Operating Instructions

1. Turn the knob on the fuel cylinder valve counterclockwise to

open.

2. Turn control knob to “HI” position.

3. Press down the control knob and hold for 30 seconds. While

holding down the control knob, press the igniter button several

times until the burner ignites. Release the control knob about

1--20 seconds after the ignition.

4. When the central burner panel remains lit, turn the control

knob to the desired position for heating.

5. Check to see the appliance operating pressure is correct

according to gas chart (page 4).

Figure 1

NOTE: If this is first time use for heater or fuel cylinder

has been replaced, it may take a couple of seconds

for the fuel to reach the heater. Continue to hold the

flame until the ceramic plaques ignite. If they do not

ignite after 15 seconds, remove the flame, close the

fuel cylinder, wait 5 minutes for any fuel to dissipate

and repeat steps 1-2.

Shutdown Instructions.

1. Turn the knob at the fuel cylinder clockwise to the OFF

position

2. Turn the control knob to the OFF position.

3. After the plaques have stopped burning (no longer glow-

ing), disconnect Regulator Hose assembly from the fuel

cylinder.

NOTE: ALWAYS INSPECT HEATER BEFORE USE AND AT

LEAST ANNUALLY BY A QUALIFIED SERVICE PERSON.

Maintenance / Storage

Always disconnect the fuel cylinder from the regulator

assembly by means of the isolating valve, and remove the

fuel cylinder from the appliance before putting appliance

into storage. If for any reason the heater is to be stored

indoors, the heater MUST be disconnected from the fuel

cylinder, and the cylinder stored outdoors in a well-venti-

lated area, out of the reach of children. The plastic valve

plug or valve cover supplied with the fuel cylinder must be

reinstalled on the valve to protect the fitting from damage.

Regularly check the hose and replace if necessary. This

appliance must be left in a safe condition, must be moved

from the danger situation such as high temperature, com-

bustible and so on. If appliance is unable to be left in a

safe condition, disconnect the fuel cylinder from appliance

and store separately, and have appliance serviced by a

qualified service person.

NOTE: There are no customer serviceable parts con-

tained within this appliance. Repair of this heater

should be done by a qualified service person.

Save all packaging materials that came with your heater,

and re-package the heater for safe storage. Be sure to

inspect the heater before each use to look for any such

obstructions such as spiderwebs. Be sure to keep the

air passage-ways, burner and combustion areas clean.

This heater should receive a thorough cleaning with com-

pressed air at least once every 30 days of operation. You

may need to clean the heater more often if conditions are

naturally dirty. Clean the Ceramic plaques using com-

pressed air below 30 PSI to prevent damage.

HOW TO CHANGE A CYLINDER

1. Cylinders must be replaced in a non-flammable and

non-smoking environment.

2. When you need to replace your empty cylinder, turn the

gas off first.

3. Make sure that the heater is extinguished completely.

4. Remove the regulator from the empty cylinder and

change a new full one.

CAUTION

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Stanley ST-11T-CPH-E in the language / languages: English as an attachment in your email.

The manual is 0,46 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Stanley ST-11T-CPH-E Manual

Product: