720591
11
Zoom out
Zoom in
Previous page
1/24
Next page
(Original instructions) ENGLISH
11
PROBLEM POSSIBLE CAUSES SOLUTION
Pump does not reach working pressure
Nozzle worn Replace nozzle
Water lter fouled Clean filter (6) (Fig. E)
Insufficient water supply Turn on water supply tap fully
Air being sucked into system Check tightness of hose fittings
Air in pump
Switch off the appliance and keep
depressing and releasing the gun trigger
until the water comes out in a steady flow.
Switch the appliance back on again.
Adjustable nozzle not positioned correctly Set nozzle (2) on (+) setting (Fig. C)
Reduce the suction height.
Thermostatic valve tripped
Water being sucked from an open container
from a height of more than 0.5 m.
Wait for correct water temperature to be restored
Pump pressure drops during
suddenly use
Water being sucked from an external tank Connect appliance to the mains water supply
Inlet water too hot Reduce temperature
Nozzle clogged Clean nozzle (Fig. E)
Inlet filter (6) fouled Clean filter (6) (Fig. E)
Motor “buzzes” but fails to start
Power supply voltage too low
Check that the voltage of the mains power supply
line is the same as that on the plate (Fig.B)
Voltage drop due to use of extension cable Check characteristics of extension cable
Appliance not used for a long period of time
Contact your nearest Authorised Service Centre
Problems with TSS device
Contact your nearest Authorised Service Centre
Motor fails to start
No electrical power
Check that the plug is firmly in the socket
and that the mains voltage supply is present (*)
Problems with TSS device
Contact your nearest Authorized Service Centre
Appliance not used for a long period of time
Using the tool unjam the motor through the
hole at the rear of the appliance (in models
with this feature) (Fig. E)
Water leakage
Seals worn
Have the seals replaced at your nearest
Authorized Service Centre
Safety valve tripped and discharging Contact an Authorized service Centre
Appliance noisy Water too hot Reduce temperature (See technical data)
Oil leakage Seals worn
Contact your nearest Authorized Service Centre
TSS versions only: Motor starts even
with gun trigger is released
High pressure system or pump hydraulic
circuit not watertight
Contact your nearest Authorized Service Centre
TSS versions only: No water delivery
when gun trigger is depressed
(With supply hose connected)
Nozzle clogged Clean nozzle (Fig. E)
No detergent sucked in
Water escapes from thermo- stat valve
Adjustable nozzle on high pressure setting
set nozzle (2) on “ ” setting (Fig.C)
Detergent too dense Dilute with water
High pressure hose extension being used Fit original hose
Deposits or restriction in detergent circuit
Water temperature inside pump head has
exceeded max. rated value stated on nameplate
Flush with clean water and eliminate
any restrictions. If the problem persists,
contact an Authorized service Centre
With appliance in operation, do not stop the
water jet for more than 5 minutes at a time
TROUBLE SHOOTING
* If the motor starts and does not restart during operation, wait 2-3 minutes before repeating the start-up procedure (overload cutout
has been tripped).
If the problem recurs more than once, contact your nearest Authorized Service Centre.
11


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Stanley SSW22 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Stanley SSW22 in the language / languages: English, French as an attachment in your email.

The manual is 1,67 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info