720738
5
Zoom out
Zoom in
Previous page
1/36
Next page
(Original instructions) ENGLISH
5
WARNING! TO REDUCE THE RISK OF INJURY,
THE USER MUST READ THE INSTRUCTION
MANUAL BEFORE USE.
Wear ear protection.
Wear safety glasses or goggles.
V Volts
Direct Current
A Amperes n
0
No-Load Speed
Hz Hertz
Class II Construction
W Watts
Earthing Terminal
min minutes
Safety Alert Symbol
Alternating
Current
/min.
Revolutions or
Reciprocation per
minute
Position of Date Code (FIG. A)
The Date Code (10), which also includes the year of
manufacture, is printed into the housing.
Example:
2017 XX JN
Year of manufacturing
PACKAGE CONTENTS
1 SST1800 table saw
1 60T saw blade
1 Blade guard
1 Miter gauge
1 Rip fence
1 Extraction hose
1 Hose adapter
2 Spanner wrench
1 Push stick
ELECTRICAL SAFETY
Your tool need to be earthed. Be sure to check that the power
supply corresponds to the voltage on the rating plate.
If the supply cord is damaged, it must be replaced
by the manufacturer or an authorised STANLEY
Service Centre in order to avoid a hazard.
FEATURES (FIG. A)
This tool includes some or all of the following features.
1. Saw table
2. Blade guard
3. Riving knife
4. Saw blade
5. Rip fence
Note: Mains voltage: When connecting to the mains, it is
imperative to verify if the voltage of the mains matches that of
the power tool. If the mains voltage exceeds the voltage
indicated on the power tool, the user may become severely
injured in an accident, and the tool may be damaged. On the
contrary, if the mains voltage is lower than the voltage
required by the tool, the motor may be damaged as a result.
Thus, if it is not possible to verify the voltage, it is imperative
not to plug in to the power source.
POWER CONNECTIONS
Before connecting the machine to the power line, make sure
the switch (s) is in the “OFF” position and be sure that the
electric current is of the same characteristics as indicated on
the machine. All line connections should make good contact.
Running on low voltage will damage the machine.
Danger! Do not expose the machine to rain or
operate the machine in damp locations.
Before connecting the machine to the power source, make
sure the switch is in the “OFF” position.
RESIDUAL RISKS
Additional residual risks may arise when using the tool which
may not be included in the enclosed safety warnings. These
risks can arise from misuse, prolonged use etc. In spite of the
application of the relevant safety regulations and the
implementation of safety devices, certain risks cannot be
avoided. These are:
Injuries caused when changing any parts, blades or
accessories.
Injuries caused by prolonged use of a tool. When using
any tool for prolonged periods ensure you take regular
breaks.
Impairment of hearing.
Health hazards caused by breathing dust developed when
using your tool (example: working with wood, especially
oak, beech and MDF.)
SAFETY OF OTHERS
This appliance is not intended for use by persons
(including children) with reduced physical, sensory or
mental capabilities, or lack of experience and knowledge,
unless they have been given supervision or instruction
concerning use of the appliance by a person responsible
for their safety.
Children should be supervised to ensure that they do not
play with the appliance.
LABELS ON TOOL
The following symbols are shown on the tool along with date
code:
5


Need help? Post your question in this forum.

Forumrules
1

Forum

stanley-sst1800

Reset search

  • which screw to open to adjust the saw blade with the table slot? Submitted on 9-10-2022 at 02:28

    Reply Report abuse
  • where to align the saw blade with the table slot for stanley SST1800w?
    Submitted on 9-10-2022 at 02:20

    Reply Report abuse


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Stanley SST1800 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Stanley SST1800 in the language / languages: English, French as an attachment in your email.

The manual is 5,11 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info