720704
6
Zoom out
Zoom in
Previous page
1/24
Next page
6
Fittingthesawblade(Fig.B)
• Hold the saw blade with the teeth facing forward.
• Push and hold the blade clamp (3) upward.
• Insert the shank of the saw blade into the blade holder as
far as it will go.
• Release the blade clamp (3).
Use
Adjusting the shoe plate for bevel cuts (Fig. C)
Warning! Never use the tool when the shoe
plate is loose or removed.
The shoe plate (6) can be set to a left or right bevel angle of
up to 45°.
• Pull the shoe plate locking lever (7) outwards to unlock the
shoe plate (6) from the 0 deg position.
• Pull the shoe plate (6) forward and set the required bevel
15°, 30° and 45° indicated in the bevel angle window.
• Push the shoe plate locking lever (7) back towards the
saw to lock the shoe plate (6).
To reset the shoe plate (6) for straight cuts:
• Pull the shoe plate locking lever (7) outwards to unlock the
shoe plate (6).
• Set the shoe plate (6) to an angle of 0º and push the shoe
plate backwards.
• Push the shoe plate locking lever (7) back towards the
saw to lock the shoe plate (6).
Fitting and removing the shoe sleeve (fig. F)
The non scratch shoe sleeve (5) should be used when
cutting surfaces that scratch easily, such as laminate,
veneer, or paint. It can also be used to protect the shoe
surface during transportation and storage.
To attach shoe sleeve:
• Place the front of the shoe plate (6) into the front of the
shoe sleeve (5).
• Lower the tool into the shoe sleeve (5). The shoe sleeve
will click securely onto the rear of the shoe.
To remove shoe sleeve:
• Grasp the shoe sleeve from the bottom at the two rear
tabs and pull down and away from the shoe plate (6).
Cutting action (fig. E)
This jig saw is equipped with four cutting actions, three
orbital and one straight. Orbital action has a more
aggressive blade motion and is designed for cutting in soft
materials like wood or plastic. Orbital action provides a
faster cut, but with a less smooth cut across the material. In
orbital action, the blade moves forward during the cutting
stroke in addition to the up and down motion..
Warning! Metal or hardwoods should never be
cut in orbital action.
• Move the cutting action lever (9) between the four cutting
positions: 0, 1, 2, and 3..
• Position 0 is straight cutting.
• Positions 1, 2, and 3 are orbital cutting.
• The aggressiveness of the cut increases as the lever is
adjusted from one to three, with three being the most
aggressive cut.
Variable speed control (fig. D)
Thevariablespeedon/offswitchoffersachoiceofspeeds
for greatly improved cutting rates in various materials.
• To set the speed, turn the variable speed control (8) to the
required setting.
Switching on and off
• Toswitchthetoolon,presstheon/offswitch(1).
• Toswitchthetooloff,releasetheon/offswitch(1).
• For continuos operation, press the lock-on button (2) and
releasetheon/offswitch(1).
• To switch the tool off when in continuous operation, press
theon/offswitch(1)andreleaseit.
Sawing
Holdthetoolrmlywithbothhandswhilecutting.Theshoe
plate(6)shouldbeheldrmlyagainstthematerialbeingcut.
This will help prevent the saw from jumping, reduce vibration
and minimise blade breakage.
6


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Stanley SSJ0650 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Stanley SSJ0650 in the language / languages: English, French as an attachment in your email.

The manual is 4,42 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info