720583
5
Zoom out
Zoom in
Previous page
1/20
Next page
SPT500
Voltage V 220 - 240
Frequency Hz 50/60
Power W 500
No-load speed /min 16,000
Air Volume m
3
/min 3.5
Weight Kg 1.6
5
ENGLISH
(Original instructions)
Electrical safety
This tool is double insulated; therefore no earth
wire is required. Always check that the power
supply corresponds to the voltage on the rating
plate.
If the supply cord is damaged, it must be replaced by the
manufacturer or an authorised Stanley Service centre in
order to avoid a hazard.
The extension cable must be suitable for outdoor use and
marked accordingly. Up to 0.75 mm² H05VV-F or H05RN-F
extension cable can be used without loss of product
performance.
Features
This tool includes the following features:
1. Nozzle
2. Blast Port
3. Trigger Switch
4. Lock-On Button
5. Suction Port
Assembly
Warning! Before assembly, make sure that the tool is
switched off and unplug.
Use
Mounting The Nozzle For Blowing Operations (fig. A)
Insert the pin located inside the Nozzle into the notch
provided on the Blast Port (1)
To lock Nozzle in place, turn the Nozzle in the direction
indicated.
To remove Nozzle, turn the Nozzle in the opposite
direction.
Operating The Blower (fig. B)
To switch your Blower on, depress the Switch (3). To
stop your Blower, release Switch.
When continuous operation is required, first depress the
switch and then the lock-on button (5) and release to
disengage lock, squeeze and release switch.
Warning: Continuous running of machine should not exceed
30 minutes.
Replacing Carbon Brushes (fig. C)
Use a screwdriver to remove the brush holder cap.
Take out the worn carbon brush, insert the new one and
secure the brush hold cap.
Warning! Remove and check the carbon brushes regularly.
Replace when they wear down to the limit mark.
Accessories
The performance of your tool depends on the accessory
used. STANLEY and Piranha accessories are engineered to
high quality standards and designed to enhance the
performance of your tool. By using these accessories you
will get the very best from your tool.
Maintenance
Your tool has been designed to operate over a long period of
time with a minimum of maintenance. Continuous
satisfactory
operation depends upon proper tool care and regular
cleaning.
Warning! Before performing any maintenance, switch off
and unplug the tool.
Regularly clean the ventilation slots in your tool using a
soft brush or dry cloth.
Regularly clean the motor housing using a damp cloth.
Do not use any abrasive or solvent-based cleaner.
Technical data
5


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Stanley SPT500 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Stanley SPT500 in the language / languages: English as an attachment in your email.

The manual is 1,38 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info