720581

Stanley SPT-302-720 Manual

18
Zoom out
Zoom in
Previous page
1/233
Next page
18
position to stop engine. Place switch in ON
position for engine to start and run.
Ignition Switch (12V DC electric start)
The ignition switch is operated by a removable
key which has 3 positions of STOP, RUN and
START.
Electric Starter & Start Button (if so equipped)
The electric starter will start a properly choked
and cranked engine when the key is turned
(12V DC) or start button (120V or 230V AC) is
pushed.
To start the machine, connect the electric
starter to an electric power source with an
approved extension cord and press the start
button.
Thoroughly inspect the electrical cord
before using the machine. If the cord is
damaged, do not operate the machine.
Replace or repair the damaged cord immediately.
Connect extension cord to the electric
starter plug-in first and then to a power
outlet; disconnect the extension cord from
the power outlet first and then from the machine.
To prevent damaging the electric starter, do
not run it more than 5 continuous seconds
each time you try to start. Wait 10 seconds
between each attempt.
Adjustments
Skid Shoes
Position the skid shoes based on surface
conditions. For removal of snow in normal
conditions, such as a paved driveway or
sidewalk, place skid shoes in the higher
position to give a 3mm (1/8”) clearance
between the scraper blade and the ground.
Use a middle or lower position when the area
to be cleared is uneven, such as a gravel
driveway.
It is not recommended to operate the snow
thrower on gravel as it can easily pick up
and throw by the impeller, causing personal
injury or damage to the snow thrower and
surrounding property.
If you choose to operate the snow thrower
on a gravel surface, use extra caution and
keep the skid shoes in position for maximum
clearance between the ground and the scraper
blade.
Always adjust skid shoes after adjusting
scraper blade to prevent premature wear to
scraper blade or damage to auger housing.
To adjust the skid shoes:
1. Loosen the four hex nuts (two on each
side) and carriage bolts. Move skid shoes
to desired position.
2. Make sure the entire bottom surface of
skid shoe is against the ground to avoid
uneven wear on the skid shoes.
3. Retighten nuts and bolts securely.
Auger Clutch and Drive Clutch
When auger clutch lever or drive clutch lever
is released and in the disengaged position, the
G
B
… 18 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Stanley SPT-302-720 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Stanley SPT-302-720 in the language / languages: English, German, French, Italian, Finnish as an attachment in your email.

The manual is 23,7 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info