720685
23
Zoom out
Zoom in
Previous page
1/104
Next page
23
ENGLISH (Original Instructions)
3. Save the left side of the cut.
Outside Corner
Left side
1. Bottom of the moulding against the fence.
2. Mitre left.
3. Save the left side of the cut.
Right Side
1. Top of the moulding against the fence.
2. Mitre right.
3. Save the right side of the cut.
Special Cuts
All cuts are made with the material secured to the
table and against the fence. Be sure to properly secure
workpiece.
Bowed Material (Fig. 35, 36)
When cutting bowed material always position it as shown
in Figure 35 and never like that shown in Figure 36.
Positioning the material incorrectly will cause it to pinch
the blade near the completion of the cut.
Cutting Plastic Pipe or Other Round Material
Plastic pipe can be easily cut with your saw. It should be
cut just like wood/ aluminum and clamped or held firmly
to the fence to keep it from rolling. This is extremely
important when making angle cuts.
Cutting Large Material (Fig. 37)
Occasionally a piece of wood will be too large to fit beneath
the blade guard. A little extra height can be gained by
rolling the guard up out of the way, as shown in Figure 37.
Avoid doing this as much as possible, but if need be, the
saw will operate properly and make the bigger cut. NEVER
TIE, TAPE, OR OTHERWISE HOLD THE GUARD OPEN
WHEN OPERATING THIS SAW.
Dust Extraction (Fig. 2, 3)
Fit the dustbag (ff) onto the dust spout (n).
WARNING: Whenever possible, connect a dust
extraction device designed in accordance with
the relevant regulations regarding dust emission.
Connect a dust collection device designed in
accordance with the relevant regulations. The air velocity
of externally connected systems shall be 20 m/s ±2 m/s.
Velocity to be measured in the connection tube at the point
of connection, with the tool connected but not running.
Transporting (Fig. 4, 5)
In order to conveniently carry the mitre saw, a carrying
handle (m) has been included on the top of the saw arm.
To transport the saw, lower the head and depress the
lock down pin (o).
Always use the carrying handle (m) or the hand
indentations (r) shown in figure 5 to transport the saw.
Maintenance
MAINTENANCE
Your STANLEY power tool has been designed to operate
over a long period of time with a minimum of maintenance.
Continuous satisfactory operation depends upon proper
tool care and regular cleaning.
Regularly clean the ventilation slots in your tool using
a soft brush or dry cloth.
Regularly clean the motor housing using a damp cloth.
Do not use any abrasive or solvent-based cleaner.This
machine is not user-serviceable. If problems occur
contact an authorised repair agent.
Lubrication
Closed-type, grease-sealed ball bearings are used
throughout. These bearings have sufficient lubrication
packed in them at the factory to last the life of the mitre
saw.
Cleaning
Before use, carefully check the upper blade guard,
movable lower blade guard as well as the dust extraction
tube to determine that it will operate properly. Ensure that
chips, dust or workpiece particle cannot lead to blockage
of one of the functions.
In case of workpiece fragments jammed between saw
blade and guards disconnect the machine from the
power supply and follow the instructions given in section
Mounting the Saw Blade. Remove the jammed parts and
reassembling the saw blade.
WARNING: Blow dirt and dust out of the main
housing with dry air as often as dirt is seen
collecting in and around the air vents. Wear
approved eye protection and approved dust
mask when performing this procedure.
WARNING: Never use solvents or other harsh
chemicals for cleaning the non-metallic parts of
the tool. These chemicals may weaken the
materials used in these parts. Use a cloth
dampened only with water and mild soap. Never
let any liquid get inside the tool; never immerse
any part of the tool into a liquid.
WARNING: To reduce the risk of injury,
regularly clean the table top.
WARNING: To reduce the risk of injury,
regularly clean the dust collection system.
To maintain products SAFETY and RELIABILITY,
repair, carbon brush inspection and replacement, any
other maintenance or adjustment should be performed
by STANLEY Service Centers, always using Stanley
replacement parts.
OPTIONAL ACCESSORIES
WARNING: Since accessories, other than those
offered by STANLEY, have not been tested with
this product, use of such accessories with this
tool could be hazardous. To reduce the risk of
injury, only STANLEY, recommended accessories should
be used with this product.
Consult your dealer for further information on the appro-
priate accessories.
23


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Stanley SM16 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Stanley SM16 in the language / languages: English, French, Turkish as an attachment in your email.

The manual is 7,33 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info