Manual Stanley SM16 (page 15 of 104) (English, French, Turkish)

720685

Zoom out

Zoom in

1/104

ENGLISH (Original Instructions)

spinning blade.

♦ Do not use another person as a substitute for a

table extension or as additional support. Unstable

support for the workpiece can cause the blade to bind

or the workpiece to shift during the cutting operation

pulling you and the helper into the spinning blade.

♦ Thecut-offpiecemustnotbejammedorpressed

byanymeansagainstthe spinning saw blade. If

confined, i.e. using length stops, the cut-off piece could

get wedged against the blade and thrown violentiy.

♦ Always use aclamp or a fixture designed to

properly support round material such as rods or

tubing. Rods have a tendency to roll while being cut,

causing the blade to “bite” and pull the work with your

hand into the blade.

♦ Let the blade reach full speed before contacting

the workpiece. This will reduce the risk of the

workpiece being thrown.

♦ If the workpiece or blade becomes jammed, turn

the mitre saw off.Wait for all moving parts to stop

and disconnect the plug from the power source

and/ or remove the battery pack. Then work to

free the jammed material. Continued sawing with

a jammed workpiece could cause loss of control or

damage to the mitre saw.

♦ After finishing the cut, release the switch, hold

the saw head down and wait for the blade to stop

before removing the cut-off piece. Reaching with

your hand near the coasting blade is dangerous.

♦ Hold the handle firmly when making an incomplete

cut or when releasing the switch before the saw

head is completely in the down position. The

braking action of the saw may cause the saw head to

be suddenly pulled downward, causing a risk of injury.

ADDITIONAL SAFETY RULES FOR MITRE

SAWS

♦ The machine is provided with a special configured

power supply cord which can only be replaced by the

manufacturer or its authorised service agent.

♦ Do not use the saw to cut other materials than those

recommended by the manufacturer.

♦ Cutting plastics, sap coated wood, and other materials

may cause melted material to accumulate on the blade

tips and the body of the saw blade, increasing the risk

of blade overheating and binding while cutting.

♦ Do not operate the machine without guards in posi-

tion, or if guards do not function or are not maintained

properly.

♦ Ensure that the arm is securely fixed when performing

bevel cuts.

♦ Keep the floor area around the machine level,

well-maintained and free of loose materials, e.g., chips

and cut-offs.

♦ Use correctly sharpened saw blades. Observe the

maximum speed mark on the saw blade.

♦ Make sure all locking knobs and clamp handles are

tight before starting any operation.

♦ Never place either hand in the blade area when the

saw is connected to the electrical power source.

♦ Never attempt to stop a machine in motion rapidly by

jamming a tool or other means against the blade; seri-

ous accidents can occur.

♦ Before using any accessory consult the instruction

manual. The improper use of an accessory can cause

damage.

♦ Use a holder or wear gloves when handling a saw

blade.

♦ Ensure that the saw blade is mounted correctly before

use.

♦ Make sure that the blade rotates in the correct

direction.

♦ Take care when slotting.

♦ Do not use blades of larger or smaller diameter than

recommended. For the proper blade rating refer to the

technical data. Use only the blades specified in this

manual, complying with EN 847-1.

♦ Consider applying specially designed noise-reduction

blades.

♦ Do not use HSS blades.

♦ Do not use cracked or damaged saw blades.

♦ Do not use any abrasive or diamond discs.

♦ Never use your saw without the kerf plate.

♦ Raise the blade from the kerf in the workpiece prior to

releasing the switch.

♦ Do not wedge anything against the fan to hold the

motor shaft.

♦ The blade guard on your saw will automatically raise

when the arm is brought down; it will lower over the

blade when head lock up release lever (cc) is pushed.

♦ Never raise the blade guard manually unless the saw

is switched off. The guard can be raised by hand when

installing or removing saw blades or for inspection of

the saw.

♦ Check periodically that the motor air slots are clean

and free of chips.

♦ Replace the kerf plate when worn. Refer to service

parts list included.

♦ Disconnect the machine from the mains before

carrying out any maintenance work or when changing

the blade.

♦ Never perform any cleaning or maintenance work

when the machine is still running and the head is not

in the rest position.

♦ When possible, always mount the machine to a bench.

♦ The front section of the guard is louvered for visibility

while cutting. Although the louvers dramatically

reduce flying debris, they are openings in the guard

and safety glasses should be worn at all times when

viewing through the louvers.

♦ Connect the saw to a dust collection device when

sawing wood. Always consider factors which influence

exposure of dust such as:

– type of material to be machined (chip board

produces more dust than wood);

– sharpness of the saw blade;

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Stanley SM16 in the language / languages: English, French, Turkish as an attachment in your email.

The manual is 7,33 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Stanley SM16 Manual

Product: