720785

Stanley SJ45 Manual

9
Zoom out
Zoom in
Previous page
1/52
Next page
(Original instructions) ENGLISH
9
Pendulum Stroke dial (Fig. G - SJ60)
• The SJ60 has these four cutting modes with increasing
amounts of pendulum action:
• Position 0: metal and aluminium and sheet metal (no
pendulum action).
• Position I: for laminates, hard wood, work tops.
• Position II: for plywood and PVC/Plastics.
• Position III: for soft wood and fast cutting
To adjust the pendulum action (Fig.G):
• Rotate the Pendulum Stroke selector (8) to the required
position.
Sawing
Hold the tool firmly with both hands while cutting (Fig.H).
The shoe plate (9) should be held firmly against the material
being cut. This will help prevent the saw from jumping, reduce
vibration and minimise blade breakage.
• Let the blade run freely for a few seconds before starting
the cut.
• Apply only a gentle pressure to the tool while performing
the cut.
Hints for optimum use
Sawing laminates
When cutting laminates, splintering may occur which can
damage the presentation surface. The most common saw
blades cut on the upward stroke, therefore if the shoe plate is
sitting on the presentation surface either use a saw blade that
cuts on the downward stroke or:
• Use a fine-tooth saw blade.
• Saw from the back surface of the workpiece.
• To minimise splintering, clamp a piece of scrap wood or
hardboard to both sides of the workpiece and saw through
this sandwich.
Sawing metal
Warning! Do not use a vacuum when cutting metal. Metal
filings will be hot and may cause fire.
Be aware that sawing metal takes much more time than
sawing wood.
• Use a saw blade suitable for sawing metal.
• When cutting thin sheet metal, clamp a piece of scrap
wood to the back surface of the workpiece and cut through
this sandwich.
• Spread a film of oil along the intended line of cut.
Rip Fence (optional)
• Ripping and circle cutting without a pencil line are easily
done with a rip fence and circle guide (available optional
spare part X43005-XJ).
Attaching Rip Fence (Figs. I )
• Insert rip fence (17) into the shoe plate slots with the cross
bar facing down as shown in figure I.
• Place screw (18) into hole in bottom of shoe plate.
• Align clamp bar (19) over screw with lipped edge facing
down and pointing towards the rear of the saw.
• Using a phillips screwdriver, run the screw into the
threaded hole in the bar clamp as shown in figure G.
• Adjust to width of cut and tighten screw.
Circle Cutting (Fig. J)
• Insert rip fence into slot on the right side of shoe plate with
cross bar facing up.
• Adjust rip fence so that distance from blade to hole in
cross bar is the desired radius and tighten screw.
• Place saw so that centre of hole in cross bar is over centre
of circle to be cut (make plunge cut, drill hole for blade or
cut inward from edge of material to get blade into
position).
• When saw is properly positioned, drive a small nail
through hole in cross bar into exact centre of circle to be
cut.
• Using rip fence as a pivot arm, begin cutting circle.
MAINTENANCE
Your STANLEY power tool has been designed to operate over
a long period of time with a minimum of maintenance.
Continuous satisfactory operation depends upon proper tool
care and regular cleaning.
• Regularly clean the ventilation slots in your tool using a
soft brush or dry cloth.
• Regularly clean the motor housing using a damp cloth. Do
not use any abrasive or solvent-based cleaner.This
machine is not user-serviceable. If problems occur contact
an authorised repair agent.
Lubrication
Your power tool requires no additional lubrication.
Cleaning
WARNING: Blow dirt and dust out of the main
housing with dry air as often as dirt is seen
collecting in and around the air vents. Wear
approved eye protection and approved dust mask
when performing this procedure.
WARNING: Never use solvents or other harsh
chemicals for cleaning the non-metallic parts of the
tool. These chemicals may weaken the materials
used in these parts. Use a cloth dampened only
with water and mild soap. Never let any liquid get
inside the tool; never immerse any part of the tool
into a liquid.
… 9 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Stanley SJ45 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Stanley SJ45 in the language / languages: English, French, Turkish as an attachment in your email.

The manual is 2,93 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info