720570

Stanley SHT-26-55 Manual

9
Zoom out
Zoom in
Previous page
1/185
Next page
9
Cold starting
– Set ignition switch 10 to "I"/"ON".
– Gently press fuel pump (14) often
enough that no more bubbles are visible
(approx. 5-6 times).
– Move the choke lever (4) to .
– Gently pull the starter grip until you feel
resistance. and then pull the pull starter forcefully
outwards until you hear a first ignition sound.
– Move the choke lever (4) to .
– Gently pull the starter grip until you feel
resistance, and then forcefully pull the starter
outwards until the
motor engages.
– Press switch-on lock 9 and gently activate the
throttle (13) at the same time.
1
2
3
4
12
11
9 8
13
5
10
14
15
16
6
7
Danger !
Danger of injury!
After the appliance has started, slightly
activate the throttle once to ensure that
the motor reaches the correct idling
speed and that the cutting equipment
does not run without a load
Note:
With the choke closed (choke lever at
), pull the pull starter only until you
hear a first ignition sound. Otherwise,
you may run the risk of fuel leaking into
the combustion chamber, which would
prevent an ignition spark.
Warm start
– Set ignition switch to I/"ON".
– Check that the choke lever is at .
– Gently pull the starter grip until you feel
resistance, and then forcefully pull the starter
outwards until the motor engages.
– Press start-up lock and gently activate the
throttle at the same time.
– If the motor does not engage after you pulled
the starter three times, repeat the starting
procedure as described under Motor cold start .
After starting the motor
– Leave the motor running at idling speed for a
while.
– Slowly press down on the throttle to increase
the motor speed.
The clutch will be released when the motor speed
is high enough, and the cutting equipment will
start to run.
– Check that the cutting equipment stops
running when you release the throttle.
Stopping the motor
– Release the throttle.
– Set ignition switch to "STOP".
The motor will switch off.
Cutting hedges
Attention !
Risk of damage to the appliance!
Take particular care close to fences!
If trimmings, fence wire or similar is
caught in the cutting equipment,
switch the appliance off immediately.
– Press the locking button (5), and keep it
pressed.
– Twist the rear handle into the desired position,
and let it engage.
G
B
… 9 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Stanley SHT-26-55 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Stanley SHT-26-55 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Swedish, Norwegian, Finnish as an attachment in your email.

The manual is 3,75 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info