Manual Stanley SHR263K (page 5 of 24) (English, French)

720442

Zoom out

Zoom in

1/24

ENGLISH (Original Instructions)

♦ Check for damage to the tool, parts or accessories

which may have occurred during transport.

♦ Take the time to thoroughly read and understand this

manual prior to operation.

ELECTRICAL SAFETY

Your tool is double insulated; therefore no earth wire

is required. Be sure to check that the power supply

corresponds to the voltage on the rating plate.

If the supply cord is damaged, it must be replaced

by the manufacturer or an authorised STANLEY

Service Centre in order to avoid a hazard.

USING AN EXTENSION CABLE

If it is necessary to use an extension cable, please used

an approved extension cable that fits the tool’s power input

specifications. The minimum cross-sectional area of the

conducting wire is 1.5 sq. mm. Cables should be untangled

before reeling up.

Cable cross-sectional

area (mm

)

Cable rated current

(Ampere)

0.75 6

1.00 10

1.50 15

2.50 20

4.00 25

Cable length (m)

7.5 15 25 30 45 60

Voltage Amperes Cable rated current (Ampere)

115 0 - 2.0 6 6 6 6 6 10

2.1 - 3.4 6 6 6 6 15 15

3.5 - 5.0 6 6 10 15 20 20

5.1 - 7.0 10 10 15 20 20 25

7.1 - 12.0 15 15 20 25 25 -

12.1 - 20.0 20 20 25 - - -

230 0 - 2.0 6 6 6 6 6 6

2.1 - 3.4 6 6 6 6 6 6

3.5 - 5.0 6 6 6 6 10 15

5.1 - 7.0 10 10 10 10 15 15

7.1 - 12.0 15 15 15 15 20 20

12.1 - 20.0 20 20 20 20 25 -

FEATURES (FIG. A, FIG.B, FIG. C, FIG. D)

This tool includes some or all of the following features.

1. Main handle

2. Lock-on button

3. Variable speed switch

4. Forward/Reverse lever

5. Mode selector switch

6. Sleeve

7. Tool clamp

8. Depth Stop

9. Side handle

10. Date code

11. SDS Plus bit

12. Drill chuck

13. Drill bit

14. Dust collector

ASSEMBLY

WARNING! Before assembly, make sure that the tool is

switched off and unplugged.

Attaching the Side Handle (FIG. A)

WARNING! When using the tool, please use the side

handle (9) for your safety.

The side handle can be fitted to suit both right-handed and

left-handled users.

♦ Turn the grip counter-clockwise until you can slide the

side handle onto the front of the tool.

♦ Rotate the side handle into the desired position.

♦ Tighten the side handle by turning the grip clockwise.

WARNING! When using the tool, remember to install the

side handles properly.

Fitting an accessory (FIG. A)

♦ Clean and grease the shank (11) of the SDS Plus bit.

♦ Insert the accessory bar into the tool clamp (7).

♦ Push the accessory down and turn it slightly until it ﬁts

into the slots.

♦ Pull on the accessory to check if it is properly locked. The

hammering and drilling function requires the accessory

to be able to move axially several centimetres when

locked in the tool clamp.

♦ To remove the accessory, pull back the sleeve (6) and

pull out the accessory from the tool clamp.

Fitting dust collector (Fig. F)

♦ Insert the SDS Plus bit (11) into dust collector (14), then

insert the bit (11) with dust collector into tool clamp (7).

♦ Use the dust collector only when the unit is used for

upright drilling (Fig. F).

USE

WARNING! Always wear gloves when you change

accessories. The exposed metal parts on the tool and

accessory may become extremely hot during operation.

Please operate tool with normal load. Do not overload. Do

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Stanley SHR263K in the language / languages: English, French as an attachment in your email.

The manual is 1,84 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Stanley SHR263K Manual

Product: