720568
17
Zoom out
Zoom in
Previous page
1/20
Next page
17
17
Problem Cause Remedy
Engine fails to start.
1. Spark plug wire disconnected.
2.Out of fuel or stale fuel.
3. Throttle control lever not in correct
starting position.
4.Choke not in ON Position.
5.Blocked fuel line.
6.Fouled spark plug.
7.Engine flooding.
8. Tine clutch control not in neutral
position.
1. Attach spark plug wire securely to
spark plug.
2.Fill with clean, fresh gasoline.
3. Move throttle control lever to start
position.
4. Chock must be positioned at CHOKE
for a cold start.
5.Clean the fuel line.
6.Clean, adjust gap, or replace.
7. Wait a few minutes to restart, but do
not prime.
8. Tine clutch control lever must be released
to neutral to start the engine.
Engine runs erratically.
1. Spark plug wire loose.
2.Unit running on CHOKE.
3.Blocked fuel line or stale fuel.
4.Vent plugged.
5.Water or dirt in fuel system.
6.Dirty air cleaner.
7.Improper carburetor adjustment.
1. Connect and tighten spark plug wire.
2.Move choke lever to OFF.
3. Clean fuel line. Fill tank with clean,
fresh gasoline.
4.Clear vent.
5. Drain fuel tank. Refill with fresh fuel.
6.Clean or replace air cleaner.
7.Refer to Engine Manual.
Engine overheats.
1. Engine oil level low.
2.Dirty air cleaner.
3.Air flow restricted.
4.Carburetor not adjusted properly.
1. Fill crankcase with proper oil.
2.Clean air cleaner.
3.Remove blower housing and clean.
4.Refer to Engine Manual.
Engine will not stop when
throttle control is positioned
at stop, or engine speed
does not increase properly
when throttle control is
adjusted.
1. Debris interfering with throttle linkage.
2. Improper throttle linkage
adjustment.
1. Clean dirt and debris.
2. Refer to Engine Manual to check and
adjust throttle linkage.
Tiller moves forward during
starting.
Tine clutch control not in neutral
position.
Tine clutch control lever must be released
to neutral to start the engine.
Tiller is difficult to control
when tilling (machine jumps
or lurches forward).
1. Improper tilling depth setting.
2. Too high engine speed on hard
ground.
1. Raise the tines for shallower tilling
by raising the depth regulator rod.
2.Set the throttle lever at lower speed.
Tines do not engage.
1. Foreign object lodged in tines.
2.Tine clevis pin(s) missing.
3.Belt worn and/or stretched.
4. Pulley and idler not in correct
adjustment.
1. Stop tiller completely, check and
discard foreign object.
2.Replace tine clevis pin(s).
3.Replace belt.
4.Contact dealer.
TROUBLE SHOOTING
G
B
17


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Stanley SGT-25-450-H at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Stanley SGT-25-450-H in the language / languages: English as an attachment in your email.

The manual is 2,39 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info