720440
6
Zoom out
Zoom in
Previous page
1/64
Next page
6
ENGLISH
(Original instructions)
Inserting and removing SDS Max accessories
(g. C,D)
This tool uses SDS Max accessories (refer to
gure D for a cross-section of an SDS Max bit shank). We
recommend to use professional accessories only.
u Clean and grease the bit shank.
u Insert the bit shank into the bit holder/tool sleeve (4).
u Push the bit down and turn it slightly until it ts into the
slots.
u Pull on the bit to check if it is properly locked. The
hammering function requires the bit to be able to move
axially several centimetres when locked in the tool
holder.
u To remove a bit pull back the tool holder/locking sleeve
(4), as illustrated in gure C, and pull out the bit.
Warning! Always wear gloves when you change accessories.
The exposed metal parts on the tool and accessory may
become extremly hot during operation.
Chipping and chiselling (Fig. E)
u Insert the appropriate chisel (Not supplied) in right
position.
u Adjust the side handle (1) as required.
u Switch on the tool and start working.
u Always switch off the tool when work is nished and
before unplugging.
u Always observe the safety instructions and applicable
regulations.
u Be aware of the location of pipework and wiring.
u Apply only a gentle pressure to the tool (approx. 5 kg).
Excessive force does not speed up chiselling but
decreases tool performance and may shorten tool life.
u Always hold the tool rmly with both hands and ensure a
secure stance. Always operate the tool with the
side handle properly mounted.
Proper hand position (Fig. F)
Warning! To reduce the risk of serious personal injury,
ALWAYS use proper hand position as shown.
Warning! To reduce the risk of serious personal injury,
ALWAYS hold securely in anticipation of a sudden reaction.
Proper hand position requires one hand on the side handle
(1), with the other hand on the main handle.
Warning! Do not use this tool to mix or pump easily
combustible or explosive uids (benzine, alcohol, etc.).
Do not mix or stir inammable liquids labelled accordingly.
Accessories
The performance of your tool depends on the accessory used.
Stanley Fat Max accessories are engineered to high quality
standards and designed to enhance the performance of your
tool. By using these accessories you will get the very best
from your tool.
Maintenance
Your Stanley Fat Max corded/cordless appliance/tool has
been designed to operate over a long period of time with a
minimum of maintenance. Continuous satisfactory operation
depends upon proper tool care and regular cleaning.
Warning! Before performing any maintenance on corded/
cordless power tools:
u Switch off and unplug the appliance/tool.
u Or switch off and remove the battery from the appliance/
tool if the appliance/tool has a separate battery pack.
u Or run the battery down completely if it is integral and then
switch off.
u Unplug the charger before cleaning it. Your charger does
not require any maintenance apart from regular cleaning.
u Regularly clean the ventilation slots in your appliance/tool/
charger using a soft brush or dry cloth.
u Regularly clean the motor housing using a damp cloth. Do
not use any abrasive or solvent-based cleaner.
u Regularly open the chuck and tap it to remove any dust
from the interior (when tted).
Mains plug replacement (U.K. & Ireland only)
If a new mains plug needs to be tted:
u Safely dispose of the old plug.
u Connect the brown lead to the live terminal in the new
plug.
u Connect the blue lead to the neutral terminal.
Warning! No connection is to be made to the earth terminal.
Follow the tting instructions supplied with good quality plugs.
Recommended fuse: 10 A.
Protecting the environment
Z
Separate collection. Products and batteries
marked with this symbol must not be disposed of
with normal household waste.
Products and batteries contain materials that can be recov-
ered or recycled reducing the demand for raw materials.
Please recycle electrical products and batteries according to
local provisions. Further information is available at
www.2helpU.com
Technical data
SFMEH220
(Type 1)
Voltage V
220 - 240
Frequency
Hz
50 - 60
Power input W
1010
6


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Stanley SFMEH220 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Stanley SFMEH220 in the language / languages: All languages as an attachment in your email.

The manual is 2,23 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info