Manual Stanley SFMEH200 (page 5 of 76) (All languages)

720438

Zoom out

Zoom in

1/76

ENGLISH

(Original instructions)

u Injuries caused by touching any rotating/moving

parts.

u Injuries caused when changing any parts, blades or

accessories.

u Injuries caused by prolonged use of a tool. When

using any tool for prolonged periods ensure you take

regular breaks.

u Impairment of hearing.

u Health hazards caused by breathing dust developed

when using your tool (example:- working with wood,

especially oak, beech and MDF.)

Vibration

The declared vibration emission values stated in the technical

data and the declaration of conformity have been measured

in accordance with a standard test method provided by

EN 60745 and may be used for comparing one tool with

another. The declared vibration emission value may also be

used in a preliminary assessment of exposure.

Warning! The vibration emission value during actual use of

the power tool can differ from the declared value depending

on the ways in which the tool is used. The vibration level may

increase above the level stated.

When assessing vibration exposure to determine safety

measures required by 2002/44/EC to protect persons regularly

using power tools in employment, an estimation of vibration

exposure should consider, the actual conditions of use and the

way the tool is used, including taking account of all parts of the

operating cycle such as the times when the tool is switched off

and when it is running idle in addition to the trigger time.

Labels on tool

The following pictograms are shown on the tool , along with

the date code:

Warning! To reduce the risk of injury, the user

must read the instruction manual.

Wear safety glasses or goggles.

Wear ear protection.

Electrical safety

This tool is double insulated; therefore no earth wire

is required. Always check that the power supply

corresponds to the voltage on the rating plate.

u If the supply cord is damaged, it must be replaced by the

manufacturer or an authorised Stanley Fat Max Service

Centre in order to avoid a hazard.

Using an extension cable

Always use an approved extension cable suitable for the

power input of this appliance (see technical data).

The extension cable must be suitable for outdoor use and

marked accordingly. Up to 30 m of 1.5 mm2 HO5VV-F exten-

sion cable can be used without loss of product performance.

Before use, inspect the extension cable for signs of damage,

wear and ageing. Replace the extension cable if damaged or

defective. When using a cable reel, always unwind the cable

completely.

Features

This tool includes some or all of the following features.

1. Main handle

2. Lock-on button

3. Variable speed switch

4. Forward/Reverse lever

5. Mode selector switch

6. Sleeve

7. SDS + Drill Chuck

8. Depth Stop

9. Side handle

10. Date code

11. SDS-Plus bit

12. Dust collector

13. Keyless chuck

Assembly

Warning! Before attempting any of the following operations,

make sure that the tool is switched off and unplugged.

Attaching the side handle (Fig A)

Warning! When using the tool, please use the side handle (9)

for your safety.

The side handle can be tted to suit both right-handed and

left-handled users.

u Turn the grip counter-clockwise until you can slide the side

handle onto the front of the tool.

u Rotate the side handle into the desired position.

u Tighten the side handle by turning the grip clockwise.

Warning! When using the tool, remember to install the side

handles properly.

Fitting an accessory (Fig A)

u Clean and grease the shank (11) of the SDS Plus bit.

u Insert the accessory bar into the SDS + Chuck (7).

u Push the accessory down and turn it slightly until it ts into

the slots.

u Pull on the accessory to check if it is properly locked.

The hammering and drilling function requires the acces-

sory to be able to move axially several centimetres when

locked in the tool clamp.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Stanley SFMEH200 in the language / languages: All languages as an attachment in your email.

The manual is 2,51 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Stanley SFMEH200 Manual

Product: