720561

Stanley SFMCST933 Manual

14
Zoom out
Zoom in
Previous page
1/146
Next page
12
ENGLISH
To extend runtime, pull the speed control switch back toward
the battery housing
12
into the "LO" position. This mode is best
for larger projects that require more time tocomplete.
To accelerate the trimmer, push the speed control switch
3
forward toward the auxillary handle
5
into the "HI" position.
This mode is best to cut through heavier growth and for
applications that need higherRPM.
NOTE: When in "HI" mode, runtime will be decreased as
compared to when trimmer is in "LO"mode.
Trimming (Fig.H, I)
With the trimmer on, angle it and swing side to side as shown
in FigureH.
Maintain a cutting angle of 5° to 10° as shown in Figure I. Do not
exceed 10°. Cut with the tip of the line.
Maintain a minimum distance of 610 mm between the guard
and your feet as shown in FigureI.
Convert to Edging Mode (Fig.J)
CAUTION: The wire edge guide should only be
used when in the edging mode.
The trimmer can be used in trimming mode or edging mode to
trim overhanging grass along lawn edges and flower beds. To
convert the trimmer to edging mode:
1. Remove the battery from thetrimmer.
2. Grasp the turn-to-edge collar
7
and pull down as shown
in Figure J.
3. Rotate the turn-to-edge collar 180° counterclockwise as
shown in Figure J., until the handle snaps back into the
upper half of the trimmer.
4. To return to trimming position, pull the turn-to-edge
collar up and rotate the head clockwise back to its
originalposition.
NOTE: You will experience faster than normal cutting line wear
if the trimmer line is positioned directly over the sidewalk or
abrasivesurface.
Edging Mode Operation (Fig.A, H)
WARNING: When being used as an edger,
stones, pieces of metal and other objects can be thrown
out at high speed by the line. The trimmer and guard are
designed to reduce the danger.
However, MAKE SURE that other persons and pets are at least
100' (30 m) away. Optimum cutting results are achieved on
edges deeper than 50mm.
• Do not use this trimmer to createtrenches.
• Using the wire edge guide
9
, guide thetrimmer.
• Position the wire edge guide on the edge of the sidewalk or
abrasive surface so the cutting line is over the grass or dirt
area to beedged.
• To make a closer cut, slightly tilt thetrimmer.
Helpful Cutting Tips (Fig.K)
• Use the tip of the string to do the cutting; do not force string
head into uncutgrass. Use edge guide along such things as
fences, houses and flower beds for bestpractices.
• Wire and picket fences cause extra string wear, even
breakage. Stone and brick walls, curbs, and wood may wear
stringrapidly.
• Do not allow spool cap
18
to drag on ground or
othersurfaces.
• In long growth, cut from the top down and do not exceed
305 mmhigh.
• Keep trimmer tilted toward the area being cut; this is the
best cuttingarea.
• The trimmer cuts when passing the unit from the left to
right. This will avoid throwing debris at theoperator.
• Avoid trees and shrubs. Tree bark, wood moldings, siding,
and fence posts can easily be damaged by thestring.
Cutting Line/Line Feeding
Your trimmer uses 1.65 mm diameter, ROUND nylon line. During
use, the tips of the nylon lines will become frayed and worn and
the special self feeding spool will automatically feed and trim
a fresh length of line. Cutting line will wear faster and require
more feeding if the cutting or edging is done along sidewalks
or other abrasive surfaces or heavier weeds are being cut. The
advanced automatic line feeding mechanism senses when more
cutting line is needed and feeds and trims the correct length
of line whenever it’s required. Do not bump unit on ground in
attempt to feed line or for any otherpurposes.
Clearing Jams and Tangled Line (Fig.K)
WARNING: Remove the battery from the
trimmer before making any assembly, adjustments or
changing accessories. Such preventive safety measures
reduce the risk of starting the applianceaccidentally.
From time to time, especially when cutting thick or stalky
weeds, the line feeding hub may become clogged with sap or
other material and the line will become jammed as a result. To
clear the jam, follow the steps listedbelow.
CAUTION: To avoid appliance damage, if the
cutting line protrudes beyond the trimming blade, cut it off
so that it just reaches theblade.
1. Remove the battery from thetrimmer.
2. Press the release tabs
19
on the spool cap
18
, and remove
the spool cap from the spool housing
10
(Figure K).
3. Pull the nylon line spool out and clear any broken line or
cutting debris from the spool area.
4. Place spool and line into spool cap with line “parked” in
slotsprovided.
5. Insert the line end through the appropriate hole in the
spool housing. Pull slack line through until it pulls out of the
holdingslots.
… 14 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Stanley SFMCST933 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Stanley SFMCST933 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 14,04 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info