Manual Stanley SFMCPH845 (page 14 of 156) (English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish)

720496

Zoom out

Zoom in

1/156

ENGLISH

To Remove the Battery Pack from the Tool

1. Press the release button

10

and firmly pull the battery pack

out of the toolhandle.

2. Insert battery pack into the charger as described in the

charger section of thismanual.

Fuel Gauge Battery Packs (Fig.C)

Some STANLEYFATMAX battery packs include a fuel gauge

which consists of three green LED lights that indicate the level of

charge remaining in the batterypack.

To actuate the fuel gauge, press and hold the fuel gauge

button

11

. A combination of the three green LED lights will

illuminate designating the level of charge left. When the level of

charge in the battery is below the usable limit, the fuel gauge

will not illuminate and the battery will need to berecharged.

NOTE: The fuel gauge is only an indication of the charge left on

the battery pack. It does not indicate tool functionality and is

subject to variation based on product components, temperature

and end-userapplication.

Joining Trimmer Head Module to Handle

Module (Fig.A, D)

Combining the handle module



11



to the trimmer head

module



12



creates a pole trimmer that is approximately 6' (1.8

m).

1. Align the groove on the outside of the coupling end of the

handle module



11



with the tongue on the inside of the

coupling end of the trimmer head module



12



2. Slide the threaded sleeve



6



on the trimmer head module

down as far as possible and rotate the sleeve clockwise until

it stops and completely covers the orangethreads.



WARNING: Always check to make sure that the sleeve is

completely threaded on and that the threads are no longer

visible. Not threading the sleeve completely on could

result in the modules becoming disconnected creating a

hazardous condition. Periodically check the connections to

insure that no threads arevisible.

Detaching Trimmer Head Module (Fig.D)



WARNING: Sharp moving blade. To prevent accidental

operation, insure that battery is disconnected from the

handle before performing the following operations. Failure

to do this could result in serious personal injury.

When detaching the modules rest the handle module

11

on the ground and grasp the center of the trimmer head

module

12

with one hand. Use your other hand to loosen the

threaded sleeve and then pull the two halves apart.

OPERATION

Instructions for Use



WARNING: Always observe the safety instructions and

applicableregulations.



WARNING: To reduce the risk of serious personal

injury, turn tool off and disconnect battery pack

before making any adjustments or removing/

installing attachments or accessories. An accidental

start-up can causeinjury.

Proper Hand Position (Fig.D)



WARNING: To reduce the risk of serious personal injury,

ALWAYS use proper hand position asshown.



WARNING: To reduce the risk of serious personal

injury, ALWAYS hold securely in anticipation of a

suddenreaction.

Always hold the trimmer, as shown in the illustrations in this

manual, with one hand on the switch handle

14

and one hand

on the foam gripper

4

( .

Pivoting the Trimmer Head (Fig.A, E)

The trimmer head pivots 180° and can be locked into 5

different positions within that range. To avoid being pinched,

weargloves.

1. Press in on the locking latch

7

and raise the trimmerhead.

2. Lock the trimmer head into any of the 5 positions. Check

to make sure that trimmer head is locked into position by

trying to move the motor housing. If it is not locked, rotate it

to the closest lockposition.

Switch (Fig.A)

To turn the tool ON pull the lock button

1

back with your

thumb and then squeeze the trigger

2

. (Once the tool is

running you can release the lock button.) To turn the tool OFF,

release the trigger.

Trimming Instructions (Fig.A, F, G)



DANGER: KEEP HANDS AWAY FROMBLADES.



WARNING: To guard against injury, observe the

following:

• READ INSTRUCTION MANUAL BEFORE USING. SAVE

INSTRUCTIONMANUAL.

• Check the hedge for foreign objects such as wires or

fences before eachuse.

• KEEP HANDS ON HANDLES. DON’TOVERREACH.

• DO NOT USE UNDER WETCONDITIONS.



CAUTION: BLADE MAY COAST AFTER TURNOFF.

NOTE: Jamming the blade on large branches can

causedamage.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Stanley SFMCPH845 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 15,91 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Stanley SFMCPH845 Manual

Product: