720423
10
Zoom out
Zoom in
Previous page
1/100
Next page
10
ENGLISH
(Original instructions)
Drilling in metal
Use a cutting lubricant when drilling metals. The exceptions
are cast iron and brass which should be drilled dry. The cutting
lubricants that work best are sulphurized cutting oil.
Drilling in masonry
For drilling in masonry, set the collar (3) to the hammer
drilling position by aligning the symbol with the marking. Use
carbide tipped masonry bits. Keep even force on the drill. A
smooth, even ow of dust indicates the proper drilling rate.
LED work light (Fig. H)
When drill is activated by pulling the trigger switch (1), the
integrated LED work light (8)will automatically illuminate the
work area.
Note: The work light is for lighting the immediate work surface
and is not intended to be used as a ashlight.
Troubleshooting
Problem Possible cause Possible solution
Unit will not start. Battery pack not
installed properly.
Battery pack
not charged.
Check battery pack
installation.
Check battery pack charg-
ing requirements
Unit starts immedi-
ately upon inserting
battery
The switch has been
left in the “on” posi-
tion.
The switch must be
moved to “off” to prevent
the tool from immediately
starting when battery is in-
serted.
Battery pack will
not charge.
Battery pack not
inserted into charger.
Charger not plugged
in.
Surrounding air
temperature too hot or
too cold.
Insert battery pack into
charger until LED lights.
Plug charger into a work-
ing outlet.
Move charger and battery
pack to a surrounding air
temperature of above 40
degrees F (45ºC) or below
105 degrees F (+40.5ºC)
Unit shuts off
abruptly.
Battery pack has
reached its maximum
thermal limit.
Out of charge. (To
maximize the life of
the battery pack it is
designed to shutoff
abruptly when the
charge is depleted
Allow battery pack to cool
down.
Place on charger
and allow to charge.
Maintenance
Your STANLEY FATMAX tool has been designed to operate
over a long period of time with a minimum of maintenance.
Continuous satisfactory operation depends upon proper tool
care and regular cleaning.
Your charger does not require any maintenance apart from
regular cleaning.
@
Warning! Before performing any maintenance on
the tool, remove the battery from the tool. Unplug the
charger before cleaning it.
Regularly clean the ventilation slots in your tool and
charger using a soft brush or dry cloth.
Regularly clean the motor housing using a damp cloth.
Do not use any abrasive or solvent-based cleaner.
Protecting the environment
Z
Separate collection. Products and batteries marked
with this symbol must not be disposed of with
normal household waste.
Products and batteries contain materials that can be
recovered or recycled reducing the demand for raw materials.
Please recycle electrical products and batteries according to
local provisions. Further information is available at
www.2helpU.com
Technical data
SFMCD711
Voltage
V
DC
18V
No-load speed
Min
-1
0-350/0-1500
Max. torque Nm 50
Chuck capacity mm 13
Max Drilling capacity
Steel/wood
/masonry
mm 13/35/13
Weight kg 1.2
Charger SFMCB11 SFMCB12 SFMCB14
Input Voltage
V
AC
230 230 230
Output Voltage
V
DC
18 18 18
Current A 1.25 2 4
Battery SFMCB201 SFMCB202 SFMCB204 SFMCB206
Voltage
V
DC
18 18 18 18
Capacity Ah 1.5 2.0 4.0 6.0
Type Li-Ion Li-Ion Li-Ion Li-Ion
Level of sound pressure according to EN60745:
Sound pressure (L
pA
) 86.5 dB(A), uncertainty (K) 3 dB(A)
Sound power (L
WA
) 97.5 dB(A), uncertainty (K) 3 dB(A)
Vibration total values (triax vector sum) according to EN60745:
Drilling into metal (a
h, D
) 2.1 m/s
2
, uncertainty (K) 1.5 m/s
2
Impact drilling into concrete (a
h, ID
) 10.1 m/s
2
, uncertainty (K) 1.5 m/s
2
10


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Stanley SFMCD711 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Stanley SFMCD711 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 2,65 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info