720477
15
Zoom out
Zoom in
Previous page
1/196
Next page
13
ENGLISH
2. To adjust saw chain tension, flip up locking tab and rotate
the bar adjust locking knob
8
counterclockwise one full
turn. Rotate the chain tensioning knob
9
clockwise until
the chain tension is correct as instructedabove.
3. Do not over-tension the chain as this will lead to excessive
wear and will reduce the life of the bar andchain.
4. Once chain tension is correct, securely tighten bar adjust
lockingknob.
NOTE: The bar adjust locking knob has a detent tightening
system. The sprocket cover is secure after three audible clicks are
heard. Further tightening is notrequired.
5. When the chain is new, check the tension frequently (after
removing battery) during the first 2 hours of use as a new
chain stretchesslightly.
Replacing the Saw Chain (Fig.A, G)
CAUTION: Sharp chain. Always wear protective gloves
when handling the chain. The chain is sharp and can cut
you when it is notrunning.
WARNING: Sharp moving chain. To prevent accidental
operation, ensure that battery is removed from the tool
before performing the following operations. Failure to do
this could result in serious personalinjury.
1. Flip up locking tab and rotate the bar adjust locking knob
8
counterclockwise to release chaintension.
2. Remove sprocket cover
6
as described in Installing the
Guide Bar and Saw Chainsection.
3. Lift the worn saw chain
5
out of the groove in the guide
bar
4
.
4. Place the new chain in the slot of the guide bar, making sure
the saw teeth are facing the correct direction by matching
the arrow on the chain with the graphic on the sprocket
cover
6
shown in FigureG.
5. Follow instructions for
Installing the Guide Bar and
SawChain
.
Replacement chain and bar are available from your nearest
STANLEYFATMAX servicecenter.
SFMCCS630 requires replacement chain # STZCS230, service
part number N580237. Replacement 30cm bar #STZCS1230,
service part numberN727097.
Saw Chain and Guide Bar Oiling (Fig.H)
Auto Oiling System
This chain saw is equipped with an auto oiling system that
keeps the saw chain and guide bar constantly lubricated. The
oil level indicator
10
shows the level of the oil in the chain
saw. If the oil level is less than a quarter full, remove the battery
from the chain saw and refill with the correct type of oil. Always
empty oil tank when finishedcutting.
NOTE: Use a high quality bar and chain oil for proper chain
and bar lubrication. As a temporary substitute, a non-detergent
SAE30 weight motor oil can be used. The use of a vegetable
based bar and chain oil is recommended when pruning trees.
Mineral oil is not recommended because it may harm trees.
Never use waste oil or very thick oil. These may damage your
chainsaw.
Filling the Oil Reservoir
1. Flip down locking lever and unscrew counterclockwise
a quarter turn and then remove the oil cap
16
. Fill the
reservoir with the recommended bar and chain oil until the
oil level has reached the top of the oil level indicator
10
.
2. Refit the oil cap and tighten clockwise a quarter turn. Flip up
locking lever to its lockedposition.
3. Periodically switch the chain saw off and check the oil
level indicator to ensure the bar and chain are being
properlyoiled.
Transporting Saw (Fig.A, I)
1. Always remove the battery from the tool and cover
the guide bar
4
with the scabbard
11
(FigureI) when
transporting thesaw.
2. Engage chain brake by pushing chain brake / front hand
guard
3
forward.
OPERATION
Instructions for Use
WARNING: Always observe the safety instructions and
applicableregulations.
WARNING: To reduce the risk of serious personal
injury, turn tool off and disconnect battery pack
before making any adjustments or removing/
installing attachments or accessories. An accidental
start-up can causeinjury.
Proper Hand Position (Fig. A, J)
WARNING: To reduce the risk of serious personal injury,
ALWAYS use proper hand position asshown.
WARNING: To reduce the risk of serious personal
injury, ALWAYS hold securely in anticipation of a
suddenreaction.
Proper hand position requires the left hand on the front
handle
13
, with the right hand on the rear handle
12
.
Operating the Chain Saw (Fig.A)
WARNING: Read and understand all instructions. Failure
to follow all instructions listed below may result in electric
shock, fire and/or serious personalinjury.
Guard Against Kickback which can result in severe
injury or death. See Important Safety Instructions
Guard Against Kickback, to avoid the risk
ofkickback.
Do not overreach. Do not cut above chest height.
Make sure your footing is firm. Keep feet apart. Divide
your weight evenly on bothfeet.
Use a firm grip with your left hand on the front
handle
13
and your right hand on the rear
handle
12
so that your body is to the left of the
guidebar.
Do not hold chain saw by front hand guard/ chain
brake
3
. Keep elbow of left arm locked so that left
arm is straight to withstand akickback.
15


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Stanley SFMCCS630 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Stanley SFMCCS630 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 23,08 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info