720799
8
Zoom out
Zoom in
Previous page
1/31
Next page
ENGLISH (Original Instructions)
8
Read instruction manual before use.
Charging Time.
Do not probe with conductive objects.
Do not charge damaged Battery.
Do not expose to water.
Have defective cords replaced immediately.
Charge only between 4 ˚C and 40 ˚C.
Only for indoor use.
Discard the battery with due care for the
environment.
Charge STANLEY Battery only with designated
STANLEY chargers. Charging Battery other
than the designated STANLEY batteries with a
STANLEY charger may make them burst or lead
to other dangerous situations.
Do not incinerate the battery.
THE PACKAGE CONTAINS
1 Screwdriver
1 USB Cable
1 Charger Adaptor
30 Bit set
1 Instruction manual
1 Warranty card
1 Service center list
Check for damage to the tool, parts or accessories
which may have occurred during transport.
Take the time to thoroughly read and understand this
manual prior to operation.
FEATURES
WARNING: Never modify the power tool or any
part of it. Damage or personal injury could result.
a. Trigger Switch
b. Handle
c. Bit Holder
d. Charger Connector
e. Charge Indicator
f. Worklight
g. Screwdriver Bit
h. Forward/Reverse Button
i. USB Cable
M
j. Charger Adaptor
USE
Removing and Installing Bits (Fig. 3)
To install the bit (g) insert into the bit holder (c) till it
snaps in place;
To remove the bit, pull it out of the bit holder.
Adjusting the Handle (Fig. 4)
The handle can be set to in-straight position and pistol
position for the optimal application required.
Note: To avoid being pinched, grasp the handle below the
pinch point shown in Fig.4.
OPERATION
Forward/Reverse Button (Fig.5)
Press the forward/reverse button (h) to the right to
make the spindle rotate counter clockwise (Fig. 5).
Press the forward/reverse button to the left to make
the spindle turn clockwise.
Note: If the forward/reverse button is left in the middle
position, the tool will not operate.
Trigger Switch (Fig. 5)
Press the trigger switch (a) for power ON.
Release the trigger switch for power OFF.
Note: If the forward/reverse button is left in the middle
position, the tool will not operate.
Worklight (Fig.1)
The worklight (j) will be activated when the trigger switch
is squeezed.
Note: The worklight is for lighting the immediate work
surface and is not intended to be used as a flashlight.
Operating in Manual Mode
The tool can be used as a conventional non-powered
screwdriver whenever the trigger switch is not depressed.
With the forward/reverse button in the middle position, the
tool will not activate.
Hints For Optimum Use
Always use the correct type of screwdriver bit.
If screws are difficult to tighten, try applying a small
amount of washing liquid or soap as a lubricant.
8


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Stanley SCS4 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Stanley SCS4 in the language / languages: English, French as an attachment in your email.

The manual is 1,67 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info