622240
17
Zoom out
Zoom in
Previous page
1/208
Next page
17
77-320 / 77-321
Abbildung F - Pendel / Transportsicherungspositionen
Abbildung G - Laser-Modi
Abbildung H - Impulsmodus
Abbildung J - Manueller Modus
Abbildung K - Nivellierungsstrahlgenauigkeit
Abbildung L - Genauigkeit des horizontalen Strahls
Abbildung M - Genauigkeit des vertikalen Strahls
Abbildung N - Genauigkeit von Auf- und Abwärtsstrahl
Tastenfeld, Modi und LED
Tastatur (Siehe Abbildung
B
)
Ein-/Aus-/ Modustaste
Impulsmodus Ein-/Ausschalttaste
Modi (Siehe Abbildung
G
)
Verfügbare Modi(SCL)
• Horizontale Linie
• Vertikale Linie
Horizontale und vertikale Linie (Kreuz)
Alle Strahlen AUS
Verfügbare Modi (SCL-D)
• Horizontale Linie
• Vertikale Linie
Horizontale und vertikale Linie (Kreuz)
Auf- und Abwärts-Punktstrahl
Alle Linien und Punkt
Alle Strahlen AUS
LEDs (Sihe Abbildung
B
)
Power LED - Leuchtet GRÜN
• Stromzufuhr EIN
Power LED - Blinkt ROT
Batterie fast leer
Power LED - Leuchtet ROT
Die Batterien müssen neu aufgeladen
werden
Arretierungs-LED - Leuchtet ROT
• Pendelarretierung EIN
• Selbstnivellierung AUS
Arretierungs-LED - Blinkt ROT
Außerhalb des Kompensierungsbereichs
Impuls-LED - Leuchtet GRÜN
• Impulsmodus EIN
(Kann mit Detektor verwendet werden)
Batterien und
Stromversorgung
Einlegen / Entfernen der Batterien
(Siehe Abbildung
C
)
Lasergerät
Drehen Sie das Laserwerkzeug um. Öffnen Sie
die Batteriefachabdeckung durch Drücken und
Herausschieben.
Legen Sie die Batterien ein bzw. nehmen Sie sie
heraus. Richten Sie die Batterien beim Einlegen in das
Lasergerät ordnungsgemäß aus.
Schließen Sie die Batteriefachabdeckung wieder, indem
Sie die Abdeckung einschieben, bis sie einrastet.
WARNUNG:
Achten Sie besonders auf die Markierungen
(+) und (-) der Batterien, sodass diese richtig
eingelegt sind. Die Batterien müssen vom
gleichen Typ sein und die gleiche Spannung
aufweisen. Verwenden Sie keine kombinierten
Batterien mit unterschiedlichen Restladungen
17


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Stanley SCL at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Stanley SCL in the language / languages: All languages as an attachment in your email.

The manual is 3,25 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info