Manual Stanley SCL-D (page 10 of 208) (All languages)

622241

Zoom out

Zoom in

1/208

77-320 / 77-321

Set Up

Mounting on Accessories

Tripod / Accessory Mount (See ﬁ gure

)

• Position a tripod / accessory in a place where it will not

be easily disturbed and near the central location of the

area to be measured.

• Set up the tripod / accessory as required. Adjust

positioning to be sure tripod head / accessory mounting

base is near horizontal.

• Remove the leg attachment from the laser tool for easier

mounting.

• Mount the laser tool to the tripod / accessory by pushing

up the center screw and tighten (Accessories with either

1/4 or 5/8 thread screw can be used).

CAUTION:

• Do not leave the laser tool unattended on an

accessory without fully tightening the center

screw. Failing to do so may lead to the laser tool

falling and sustaining possible damage.

NOTE:

• It is best practice to always support laser tool with

one hand when placing or removing laser tool from an

accessory.

• If positioning over a target, partially tighten the center

screw, align laser tool, and then fully tighten.

Operation

NOTE:

• See LED Descriptions for indications during operation.

• Before operating the laser tool always be sure to check the

laser tool for accuracy.

• In Manual Mode, Self-Levelling is OFF. The accuracy of the

beam is not guaranteed to be level.

• Laser tool will indicate when it is out of compensation

range. Reference LED Descriptions. Reposition laser tool

to be closer to level.

• When not in use, please be sure to power OFF the laser

tool and place the pendulum lock in the locked position.

Power

• Press

to turn laser tool ON.

• To turn laser tool OFF, repeatedly press

until the

OFF mode is selected OR press and hold

for ≥ 3

seconds to turn laser tool OFF while in any mode.

Mode

• Press

repeatedly to cycle through the available

modes.

Self-Levelling / Manual Mode

(See Figures

and

)

• The pendulum lock on the laser tool needs to be

switched to the unlocked position to enable self-

levelling.

• The laser tool can be used with the pendulum lock in

the locked position when it is required to position the

laser tool at various angles to project non-level straight

lines or points.

Pulse Mode (See Figure

)

• When laser tool is ON, press

to turn ON / OFF

pulse mode.

• Pulse mode allows use with laser detector.

Applications

Plumb / Point Transfer

• Using the vertical laser beam, establish a vertical reference

plane.

• Position the desired object(s) until they are aligned with the

vertical reference plane to ensure object(s) are plumb.

(SCL-D only):

• Establish 2 reference points that need to be plumb.

• Align either the down laser beam or the up laser beam to a

set reference point.

• The opposing laser beam(s) will be projecting a point which

is plumb.

• Position the desired object until the laser beam is aligned

with the second reference point that needs to be plumb

with the set reference point.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Stanley SCL-D in the language / languages: All languages as an attachment in your email.

The manual is 3,25 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Stanley SCL-D Manual

Product: