622246

Stanley RLD400 Manual

6
Zoom out
Zoom in
Previous page
1/104
Next page
6
77-132 / 77-133
To mount clamp onto measuring rod, pole, or similar object
(See fi gure
E
) :
• Loosen tightening knob.
• Place onto measuring rod, pole, or similar object.
• Tighten knob to secure the clamp.
• When locating reference level loosen clamp to allow for
up / down positioning.
• When reference level is found, tighten knob again to
secure.
Operation
(See Keypad and LCD Descriptions for indications during
operation)
Power
• Press
to turn detector ON.
• When powered ON, the entire LCD will momentarily
display all icons (this allows a check to ensure that LCD
is functioning correctly).
• Press and hold
for ≥ 3 seconds to turn detector
OFF.
NOTE:
• The detector will automatically power OFF after 10 minutes
of not detecting a laser beam to conserve battery. To power
ON again, press
.
Illuminate LCD
• When detector is ON, press
to turn ON / OFF LCD
illumination.
NOTE:
The illumination will automatically turn OFF after 60 seconds of
not detecting a laser beam or having a key pressed.
Accuracy
• When powered ON, press
to toggle accuracy
setting between HIGH and LOW.
• When powered ON, the default accuracy setting is set
to HIGH.
NOTE:
• Only select LOW accuracy setting in times where HIGH
accuracy is not needed and / or when a stable reference
level cannot be obtained due to slight vibrations at or near
the work site.
• If the point to be measured is at a longer distance the LOW
accuracy setting may be necessary due to heat waves or
slight vibrations that may interfere with obtaining a stable
reference level.
Speaker Volume
• When powered ON,
press to toggle through the
volume settings (LOUD / SOFT / MUTE).
• When powered ON, the default volume setting is set
to LOUD.
Detecting Reference Level
• With detector ON, position within the general area
where the laser beam being referenced is being
projected towards.
• Use the bubble vial to maintain a level plane with the
detector.
• Be sure laser reception window is facing the direction of
the laser beam source.
• Move detector as indicated on the LCD to align datum
with laser beam.
• If speaker volume is ON (LOUD / SOFT), an audible tone
will sound to assist in communicating the positioning
of the detector.
• A beeping tone signals that the laser beam has been
detected. A fast beeping tone signals the detector
must be moved down. A slower beeping tone signals
the detector must be moved up. Again, the LCD also
indicates the direction the detector must be moved.
• A steady tone indicates that the laser beam is aligned
with the datum line on detector.
NOTE:
• When detecting the reference level the laser reception
window must face towards the laser source within a 40°
range from left to right.
Marking (See fi gure
E
)
• Once the reference level has been detected, the position
can be marked at the datum line.
NOTE:
• Be sure to reference the back of the detector for the
measurement compensation value (distance from top to
datum) if the top of the detector was used as a marking
location.
… 6 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Stanley RLD400 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Stanley RLD400 in the language / languages: All languages as an attachment in your email.

The manual is 2,27 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info