622260
14
Zoom out
Zoom in
Previous page
1/310
Next page
14
77-496 / 77-429 / 77-439 / 77-497 / 77-427
it is preferable to use the remote whenever possible to
perform functions (when available).
Laser tool is Auto-Levelling by default.
Tilt Warning is ON by default when laser tool leaves the
manufacturer.
Tilt Warning is only available in the Auto-Levelling modes.
Tilt Warning is not available while in Manual Mode.
Power
• Press
to turn laser tool ON / OFF.
When powered ON, Tilt Warning is ON by default
(default setting can be changed).
When powered ON, Laser tool begins Auto-Levelling.
When Auto-Levelling has completed laser will rotate at
last used RPM speed setting.
Tilt Warning (not available in Manual Mode)
When powered ON, Tilt Warning is ON by default.
When powered ON, press
to turn Tilt Warning
ON / OFF.
With Tilt Warning ON, laser tool will indicate with LED
/ LCD and blinking laser beam when the laser tool has
sensed any movement.
If an alarm has been triggered, press
to reset.
When reset, the laser tool begins Auto-Levelling. Check
alignment with original target.
Tilt Warning Default Setting
When powered OFF, press and hold
followed
by .
Release both keys.
If Tilt LED / Icon is ON, default setting is ON. If Tilt LED /
Icon is OFF default setting is OFF.
Laser tool begins Auto-Levelling as done when normally
powered ON.
Repeating the steps will toggle ON / OFF the Tilt
Warning default setting.
Manual Mode
When powered ON, press and hold
for ≥ 3
seconds to turn ON / OFF Manual Mode.
Auto-Levelling is OFF in Manual Mode.
Laser tool can be manually positioned at any angle.
When Manual Mode is turned OFF, laser tool begins
Auto-Levelling as done when initially powered ON.
Calibration Mode - see Accuracy Check and
Calibration section
Manual Slope Mode
(For RL HW / RL HW+ substitute
where ever
is referenced below)
When powered ON, press
. Manual Mode turns
ON, Auto-Levelling OFF.
(For RL HGW
needs to be pressed and held for
≥ 3 seconds to enter Manual Mode prior to pressing
noted above)
LED / LCD will indicate “X” axis adjust. Press
to adjust axis.
LED / LCD will indicate when at maximum slope angle.
The axis will not move any further in that direction.
• Press
again to set the “X” axis and / or proceed to
the “Y” axis adjust.
LED / LCD will indicate “Y” axis adjust. Press
to adjust axis.
LED / LCD will indicate when at maximum slope angle.
The axis will not move any further in that direction.
• Press
again to set the “Y” axis and / or proceed to
use of laser tool in Manual Slope Mode.
“X” and “Y” axis are now set at manually adjusted
slopes.
To turn Manual Slope Mode OFF, press and hold
for ≥ 3 seconds.
When Manual Mode is turned OFF, laser tool begins
Auto-Levelling as done when initially powered ON.
14


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Stanley RL HWplus at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Stanley RL HWplus in the language / languages: All languages as an attachment in your email.

The manual is 1,8 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info