622262

Stanley RL HV Manual

15
Zoom out
Zoom in
Previous page
1/310
Next page
15
77-496 / 77-429 / 77-439 / 77-497 / 77-427
NOTE:
• A single press of
will change slope by 0,01%.
• Holding the key down will move the slope axis
continuously, slowly at fi rst, followed by a faster rate
when held for an extended time.
• Reference Figure
L
for resulting slope direction for
each key.
Speed
• Press
to toggle through the available speed
settings from fastest to slowest to stopped.
Spot Mode
• Press
to stopped (0 RPM) setting.
• Press
to rotate the direction of the spot.
NOTE:
• A single press of
will rotate the direction
by 0,10°.
• Holding down the key will rotate the direction
continuously, slowly at fi rst, followed by a faster rate
when held for an extended time.
• The laser will blink 3 x prior to moving at the faster rate.
• Reference Figure
M
for resulting rotation direction
for each key.
Scan Mode
• Press
to cycle through available scan angles (15°
/ 45° / 90°).
• Press
to rotate the direction of the scan.
• Press
to turn OFF Scan Mode and return to the last
used speed setting.
NOTE:
• A single press of
will rotate the direction
by 2,0°.
• Holding down the key will rotate the direction
continuously, slowly at fi rst, followed by a faster rate
when held for an extended time.
• The laser will blink 3 x prior to moving at the faster rate.
• Reference Figure
M
for resulting rotation direction
for each key.
Digital Slope Mode (with Auto-Levelling)
• When powered ON, press
.
• LCD will indicate “X” axis adjust. Press
to
adjust axis value.
• LCD will indicate when at maximum slope angle. The
value will not continue any further in that direction.
• Press
again to set the “X” axis and / or proceed to
the “Y” axis value adjust.
• LCD will indicate “Y” axis adjust. Press
to
adjust axis value.
• LCD will indicate when at maximum slope angle. The
value will not continue any further in that direction.
• Press
again to set the “Y” axis and / or proceed to
use of laser tool in Digital Slope Mode.
• Laser tool begins Auto-Levelling as done when initially
powered ON and then the “X” and “Y” axis will slope to
the set values.
• To turn Digital Slope Mode OFF, the laser tool power
needs to be cycled. Press
2x to power OFF and
back ON.
NOTE:
• A single press of
will change the value by
0,01%.
• Holding the key down will move the value continuously,
slowly at fi rst, followed by a faster rate when held for
an extended time.
… 15 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Stanley RL HV at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Stanley RL HV in the language / languages: All languages as an attachment in your email.

The manual is 1,8 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info