622262
12
Zoom out
Zoom in
Previous page
1/310
Next page
12
77-496 / 77-429 / 77-439 / 77-497 / 77-427
Batteries and Power
Battery Installation / Removal
(See fi gure
F
and
G
to reference battery location of
laser tool and remote control)
Laser Tool (See fi gure
F
)
Press tabs to open battery compartment and slide out.
Install / Remove batteries. Orient batteries correctly
when placing into laser tool.
Securely close and lock battery compartment cover.
IR Remote Controller (See fi gure
G
)
Open battery compartment by sliding cover off.
Install / Remove batteries. Orient batteries correctly
when placing into laser tool.
Securely close and lock battery compartment cover.
WARNING:
Pay close attention to the battery holder’s (+)
and (-) markings for proper battery insertion.
Batteries must be of same type and capacity. Do
not use a combination of batteries with different
capacities remaining.
Charging Battery
For best life, the rechargeable battery must be charged for
4 hours before fi rst use.
Plug charging / power adapter plug into charging jack of
laser tool
Plug charging / power adapter into power outlet (110 V or
220 V) with appropriate plug receptacle.
The LED on the charging / power adapter will light RED
during charge.
Leave battery to charge for approximately 4 hours to reach
full charge.
When battery is fully charged unplug the charging / power
adapter from laser tool and power outlet.
The LED on the charging / power adapter will light GREEN
when charge is complete.
WARNING:
• Use charging / power adapter only with Ni-MH
battery pack supplied. Charging any other
type of battery may result in damage and/or
personal harm.
WARNING:
The battery and charging / power adapter can be
damaged if damp. Always store and charge the
tool in a dry and covered place.
NOTE:
For best battery life, it is recommended to charge the
battery once it has been fully discharged and avoid letting
charge for > 10 hours at a time.
Operating with Charging / Power
Adapter
Laser tool can operate while plugged into charging / power
adapter.
Functions and controls of laser tool are the same as when
not plugged into charging / power adapter.
Set Up
Positioning
(See Feature Set to reference which models offer Auto-
Levelling in the given positions)
Horizontal Position (See fi gure
A
)
Place laser tool down on its bottom. Be sure surface is
near level. Press
to power ON.
Vertical Position (See fi gure
B
)
Place laser tool down on its side, handle facing up. Be
sure surface is near level. Press
to power ON.
12


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Stanley RL HV at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Stanley RL HV in the language / languages: All languages as an attachment in your email.

The manual is 1,8 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info