622261

Stanley RL HGW Manual

17
Zoom out
Zoom in
Previous page
1/310
Next page
17
77-496 / 77-429 / 77-439 / 77-497 / 77-427
exit Calibration Mode.
• Axis settings are now saved, Calibration Mode is OFF,
and laser tool begins Auto-Levelling as done when
initially powered ON.
NOTE:
• A press of
will slope the axis by 3,5 arc
seconds. Reference Figure
L
for resulting slope direction
for each key.
• If the laser tool can still not be calibrated after
following the Calibration procedure, please send
the laser tool into an Authorized Service Center for
repair.
Vertical Check (See Figure
P
)
(Only necessary on models with Vertical Auto-Levelling)
• Set the laser tool on a stable surface in its vertical
position 1 m away from a wall that extends ≥ 2 m high
with the ”Y1” side facing that wall (
P
1
).
• Power ON the laser tool and allow the laser tool to
Auto-Level and be sure laser is rotating.
• Mark reference points “A” (where laser line is on
fl oor 1 m away from wall), “B “ (where laser beam
is at corner), and “D
1
” (where laser beam is 2 m
up the wall).
• Rotate the laser tool 180° so that the “Y2” side is now
facing the wall (
P
2
).
• Align the laser beam with reference points “A” and “B”
and then go back to the wall and measure the distance
between the reference point “D
1
” and “D
2
” (
P
3
).
• There is no need to adjust calibration if the distance
between reference point “D
1
” and “D
2
” is < 1,0 mm.
• If the distance measured is ≥ 1,0 mm then a calibration
adjustment is necessary.
Vertical Calibration (See Figure
P
)
(For RL HW+ substitute
where ever is
referenced below)
• With laser tool powered OFF, press and hold
followed by
.
• Release
and continue to hold for ≥ 3
seconds.
• Release
.
• The LED/LCD will indicate laser tool is in Calibration
mode.
• If necessary, adjust the vertical “X” axis by pressing
until the laser beam is aligned with “D
0
”.
“D
0
” is the halfway point between “D
1
” and “D
2
”
during vertical axis check.
• .
• Press to set the vertical “X” axis.
• Axis setting is now saved, Calibration Mode is OFF,
and laser tool begins Auto-Levelling as done when
initially powered ON.
NOTE:
• A press of
will slope the axis by 3,5 arc
seconds. Reference Figure
L
for resulting slope direction
for each key.
• If the laser tool can still not be calibrated after
following the Calibration procedure, please send
the laser tool into an Authorized Service Center for
repair.
… 17 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Stanley RL HGW at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Stanley RL HGW in the language / languages: All languages as an attachment in your email.

The manual is 1,8 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info