720717
4
Zoom out
Zoom in
Previous page
1/35
Next page
6
ENGLISH
(Original instructions)
7
ENGLISH
(Original instructions)
Features
This tool includes some or all of the following features.
1. On/off switch
2. Lock-off button
3. Shavings discharge outlet
4. Shavings discharge outlet selector
5. Planing depth adjustment knob
6. Planing depth graduation
Assembly
Warning! Before assembly, make sure that the tool is
switched off and unplugged.
Replacing the cutting blades (g.A)
The cutting blades provided with this tool are reversible.
Replacement cutting blades can be obtained from your local
retailer.
Removing
u Loosen the bolts (7) using the spanner supplied.
u Slide the blade (8) out of the holder.
u Reverse the blade so that the unused side comes in posi-
tion. If both sides are worn, the blade must be replaced.
Fitting
u Slide the blade into the holder until it is against the end
stop.
u Tighten the bolts using the spanner supplied.
Warning! Always replace both cutters.
Adjusting the depth of cut (g. B)
The depth of cut is indicated by the marking (9). The setting
range can be read from the graduation (6).
u Turn the planing depth adjustment knob (5) to the required
depth of cut.
u Turn the knob to the ‘P' postion whenever the tool is not in
use.
Fitting and removing the parallel fence (g. C)
The parallel fence is used to for optimum control on narrow
workpieces.
u Thread the knob (11) into the hole on the side of the
planer and securely tighten.
u Loosen the parallel fence adjustment knob (10).
u Slide the parallel fence into the desired position.
u Securely tighten the parallel fence adjustment knob.
Note: The parallel fence should be below the planer when
installed correctly.
u To remove the parallel fence proceed in reverse order.
Connecting a vacuum cleaner to the tool (g. D)
An adaptor is required to connect a vacuum cleaner or dust
extractor to the tool. The adaptor can be purchased from your
local Stanley Fat Max retailer.
u Slide the adaptor (12) over the shavings discharge outlet
(3).
u Connect the vacuum cleaner hose (13) to the adaptor.
Fitting the shavings collection bag (g. E)
The shavings collection bag is particularly useful when work-
ing in conned spaces.
u Slide the connecting plate (14) of the bag over either side
of the shavings discharge outlet (3).
u To prevent chips from coming out opposite side of shav-
ings discharge outlet, move the shavings discharge outlet
selector (4) to the opposite side from the bag.
Emptying the shavings collection bag
The shavings collection bag should be emptied regularly while
using it to prevent blocking.
u Unzip the bag and empty it before continuing.
Use
Warning! Let the tool work at its own pace. Do not overload.
Switching on and off
Switching on
u Keep the lock-off button (2) depressed and press the on/
off switch (1).
u Release the lock-off button.
Switching off
u Release the on/off switch.
Planing
u Hold the tool with the nose piece of the shoe resting on
top of the workpiece surface.
u Switch the tool on.
u Move the tool steadily forward to perform the cutting
stroke.
u Switch the tool off after the stroke has been completed.
Rebating (g. F)
u Fit and adjust the parallel fence.
u Proceed as for planing.
Chamfering edges (g. G)
The V-groove in the nose piece of the shoe enables you to
chamfer edges at 45°, 30° and 15° angles.
u Hold the tool at an angle with the desired groove (20)
around the edge of the workpiece and perform the cutting
stroke.
Parking rest (g. H)
Your planer is equipped with a parking rest (21) that automati-
cally lowers into place when the tool is lifted from the work
surface. When planing, the parking foot raises as the tool is
pushed forward. When the parking foot is lowered, the planer
can set on the work surface without the blade touching.
Hints for optimum use
u Move the tool along the grain of the wood.
u If the grain is cross or curly, or if the workpiece material is
a hard type of wood, adjust the depth of cut to take only a
very thin shaving at each pass and take several passes to
achieve the desired result.
u To keep the tool in a straight line, press down the front of
the tool at the start, and press down the back of the tool at
the end of the cutting stroke.
Accessories
The performance of your tool depends on the accessory used.
Stanley Fat Max and Piranha accessories are engineered to
high quality standards and designed to enhance the perfor-
mance of your tool. By using these accessories you will get
the very best from your tool.
The following types of cutting blades can be obtained from
your local retailer:
- Tungsten carbide tipped reversible cutting blades (part
no. X35007, supplied per pair)
- High-speed steel reversible cutting blades (part no.
X24192-XJ11, supplied per pair)
Maintenance
Your tool has been designed to operate over a long period of
time with a minimum of maintenance. Continuous satisfactory
operation depends upon proper tool care and regular cleaning.
Warning! Before performing any maintenance, switch off and
unplug the tool.
u Regularly clean the ventilation slots in your tool using a
soft brush or dry cloth.
u Regularly clean the motor housing using a damp cloth. Do
not use any abrasive or solvent-based cleaner.
Replacing the drive belt (g. I)
u Loosen the screws (15) and remove the cover (16).
u Remove the old drive belt.
u Place the new belt (17) over the pulleys. Place the belt
over the large pulley (18) rst, then over the small pulley
(19), whilst manually rotating the belt steadily.
u Put the cover back in place and tighten the screws.
Replacing the drive belt (g. I)
Brushes should be regularly inspected for wear.
u Remove brush cap (22). The brushes should slide freely
in brush box. If brushes are worn down to .3" (8mm) they
should be replaced.
To reinstall, push new brush back into brush box. If replacing
existing brush, maintain same orientation as when removed.
Replace the brush cap (do not overtighten).
Mains plug replacement (U.K. & Ireland only)
If a new mains plug needs to be tted:
u Safely dispose of the old plug.
u Connect the brown lead to the live terminal in the new
plug.
u Connect the blue lead to the neutral terminal.
Warning! No connection is to be made to the earth terminal.
Follow the tting instructions supplied with good quality plugs.
Recommended fuse: 5 A
Protecting the environment
Z
Separate collection. Products and batteries
marked with this symbol must not be disposed
of with normal household waste.
Products and batteries contain materials that can be recov-
ered or recycled reducing the demand for raw materials.
Please recycle electrical products and batteries accord-
ing to local provisions. Further information is available at
www.2helpU.com.
Technical data
KFFMEW630
(Type 1)
FME630
(Type 1)
Input voltage V
AC
230 230
Power input W
750 750
No-load speed min
-1
16,500 16,500
Planing width mm
82 82
Planing depth mm
2 2
Rebating depth mm
12 12
Weight
kg
2.9 2.9
Level of sound pressure according to EN62841:
L
pA
(sound pressure) 90.5 dB(A), Uncertainty (K) 3 dB(A)
L
WA
(sound power) 101.5 dB(A), Uncertainty (K) 3 dB(A)
Vibration total values (triax vector sum) according to EN62841:
Vibration emission value (a
h
) 4.1 m/s
2
, uncertainty (K) 1.5 m/s
2
4


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Stanley KFFMEW630 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Stanley KFFMEW630 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 5,18 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info