720698

Stanley KFFMES340 Manual

6
Zoom out
Zoom in
Previous page
1/8
Next page
6
ENGLISH
(Original instructions)
u
Slide the shoe plate forward to release it from the 0° posi-
tive stop position.
u
Set the shoe plate to the desired bevel angle. Use a
protractor to verify angle accuracy.
u
Push the shoe beveling lever (6) back towards the saw to
lock the shoe plate (5).
Note: The shoe can be beveled to the left or to the right and
has detents at 15°, 30° and 45°.
To reset the shoe for straight cuts:
u
Pull the shoe beveling lever (6) out and away from the
saw to unlock the shoe plate (5).
u
Rotate shoe to an angle of approximately 0° and then pull
shoe backwards to engage the 0° positive stop.
u
Push the shoe beveling lever back (6) towards the saw to
lock the shoe plate (5).
Cutting action (g. F)
This jig saw is equipped with four cutting actions, three orbital
and one straight. Orbital action has a more aggressive blade
motion and is designed for cutting in soft materials like wood
or plastic. Orbital action provides a faster cut, but with a less
smooth cut across the material. In orbital action, the blade
moves forward during the cutting stroke in addition to the up
and down motion..
Warning! Metal or hardwoods should never be cut in orbital
action.
u
Move the cutting action lever (8) between the four cutting
positions: 0, 1, 2, and 3..
u Position 0 is straight cutting.
u
Positions 1, 2, and 3 are orbital cutting.
u
The aggressiveness of the cut increases as the lever is
adjusted from one to three, with three being the most
aggressive cut.
LED worklight
The tool is equipped with an LED worklight (10) which projects
on the cutting path.
u
The LED worklight (10) will come on when the trigger
switch (1) is pressed and will go off when the trigger
switch (1) is released..
Sawing
u
Always hold the tool with both hands.
u
Let the blade run freely for a few seconds before starting
the cut.
u
Apply only a gentle pressure to the tool while performing
the cut.
u
If possible, work with the shoe plate (5) pressed against
the workpiece. This will improve tool control and reduce
tool vibration, as well as prevent the blade from being
damaged.
Hints for optimum use
General
u
Use a high speed for wood, a medium speed for alu-
minium and PVC and a low speed for metals other than
aluminium.
Sawing laminates
As the saw blade cuts on the upward stroke, splintering may
occur on the surface closest to the shoe plate.
u
Use a ne-tooth saw blade.
u
Saw from the back surface of the workpiece.
u
To minimise splintering, clamp a piece of scrap wood or
hardboard to both sides of the workpiece and saw through
this sandwich.
Sawing metal
Be aware that sawing metal takes much more time than
sawing wood.
u
Use a saw blade suitable for sawing metal. Use a ne-
tooth saw blade for ferrous metals and a coarser saw
blade for non-ferrous metals.
u
When cutting thin sheet metal, clamp a piece of scrap
wood to the back surface of the workpiece and cut through
this sandwich.
u
Spread a lm of oil along the intended line of cut.
Accessories
The performance of your tool depends on the accessory used.
Stanley Fat Max accessories are engineered to high quality
standards and designed to enhance the performance of your
tool. By using these accessories you will get the very best
from your tool.
This tool is suitable both for U-shank and T-shank saw blades.
Maintenance
Your tool has been designed to operate over a long period of
time with a minimum of maintenance. Continuous satisfactory
operation depends upon proper tool care and regular cleaning.
Warning! Before performing any maintenance, switch off and
unplug the tool.
u
Regularly clean the ventilation slots in your tool and
charger using a soft brush or dry cloth.
u
Regularly clean the motor housing using a damp cloth. Do
not use any abrasive or solvent-based cleaner.
u
Occasionally apply a drop of oil to the axle of the blade
support roller.
6


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Stanley KFFMES340 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Stanley KFFMES340 in the language / languages: English as an attachment in your email.

The manual is 0,94 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Stanley KFFMES340

Stanley KFFMES340 Quick start guide - All languages - 104 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info