720433

Stanley KFFMED1250 Manual

11
Zoom out
Zoom in
Previous page
1/52
Next page
11
(Übersetzung der ursprünglichen Anweisungen)
DEUTSCH
mum drilling depth is equal to the distance between the tip
of the drill bit and the front end of the depth stop.
uTighten the knob (9).
Fittinganaccessory(g.B)
uClean and grease the shank (10) of the accessory.
uPull back the sleeve (11) and insert the shank into the tool
holder (5).
uPush the accessory down and turn it slightly until it ts into
the slots.
uPull on the accessory to check if it is properly locked. The
hammering function requires the accessory to be able to
move axially several centimetres when locked in the tool
holder.
uTo remove the accessory, pull back the sleeve (11) and
pull out the accessory.
Use
Warning! Let the tool work at its own pace. Do not overload.
Warning! Before drilling into walls, oors or ceilings, check for
the location of wiring and pipes.
Warning! Do not apply chisels when the tool is in the drilling
mode.
Selectingtheoperatingmode(g.D)
The tool can be used in three operating modes.
u To operate the drilling mode selector (3), rotate it towards
the required position, as indicated by the symbols.
u To operate the operating mode selector (4), push the
unlock button (16) and rotate the selector towards the
required position, as indicated by the symbols.
Drilling
u For drilling in steel, wood and plastics, and for screwdriv-
ing set the operating mode selector (4) to the
s
position
and the drilling mode selector (3) to the
r
position.
Hammer drilling
u For hammer drilling in masonry and concrete, set the
operating mode selector (4) to the
s
position and the
drilling mode selector (3) to the
s
position. When ham-
mering, the tool should not bounce and run smoothly. If
necessary, increase the speed.
Hammering
u For hammering with spindle lock, and for light chiselling
and chipping, set the operating mode selector (4) to the
q
position and the drilling mode selector (3) to the
s
position.
u When changing from hammer drilling to chiselling, turn
the chisel to the desired position. If resistance is felt
during mode change, slightly turn the chisel to engage the
spindle lock.
Switching on and off
u Select the required speed by turning the speed selector
dial (2).
u To switch the tool on, press the on/off switch (1).
u To switch the tool off, release the on/off switch.
Brushmonitor(g.C)
Your tool has a built in system that monitors the health of the
brushes.
u Green brush monitor indicator (17). The brushes are in
good condition.
u Red brush monitor indicator (18). The brushes are warn
and need replacing, return your tool to an authorised
Stanley Europe Service Centre in order to to have the
brushes replaced.
Accessories
The performance of your tool depends on the accessory used.
Stanley Fat Max accessories are engineered to high quality
standards and designed to enhance the performance of your
tool. By using these accessories you will get the very best
from your tool.
Maintenance
Your Stanley Fat Max corded/cordless appliance/tool has
been designed to operate over a long period of time with a
minimum of maintenance. Continuous satisfactory operation
depends upon proper tool care and regular cleaning.
uSwitch off and unplug the appliance/tool.
uRegularly clean the ventilation slots in your appliance/tool/
charger using a soft brush or dry cloth.
uRegularly clean the motor housing using a damp cloth. Do
not use any abrasive or solvent-based cleaner.
uRegularly open the chuck and tap it to remove any dust
from the interior (when tted).
Mains plug replacement (U.K. & Ireland only)
If a new mains plug needs to be tted:
uSafely dispose of the old plug.
uConnect the brown lead to the live terminal in the new
plug.
uConnect the blue lead to the neutral terminal.
Warning! No connection is to be made to the earth terminal.
Follow the tting instructions supplied with good quality plugs.
Recommended fuse: 5 A.
… 11 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Stanley KFFMED1250 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Stanley KFFMED1250 in the language / languages: English, German, French, Polish, Portuguese, Turkish, Spanish as an attachment in your email.

The manual is 3,09 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info