720749

Stanley FMHT77598 Manual

10
Zoom out
Zoom in
Previous page
1/220
Next page
10
GB
7.
If your measurement is greater than the Allowable
Distance Between P1 & P3 for the corresponding
Distance Between P1 & P2 in the following table, the laser
must be serviced at an authorized service center.
Distance Between
P1 & P2
Allowable Distance
Between P1 and P3
9 m (30’) 6 mm (1/4”)
12 m (40’) 8 mm (5/16”)
15 m (50’) 10 mm (13/32”)
Horizontal Line Accuracy - Tilt
Checking the tilt of the laser’s horizontal line requires a at
vertical surface at least 30’ (9m) wide.
1.
Place a tripod as shown in Figure
F
1
, which is:
• At the center of the wall (D 1/2).
• In front of the wall at a distance of half the size of the wall
(D 1/2).
2.
Place the laser on a tripod and screw the threaded knob on
the tripod into the female thread on the laser.
3.
Slide the laser’s Power/Transport Lock switch to the right to
turn the laser ON (Figure
A
7
).
2.
Press 3 times to display a horizontal line and a vertical
line.
3.
Aim the laser’s vertical line at the rst corner or reference
point (Figure
F
1
).
4.
Measure half the distance across the wall (D1/2).
5.
Where the horizontal laser line crosses the halfway point
(D1/2), mark point P1.
6.
Rotate the laser to another corner or reference point
(Figure
F
2
).
7.
Where the horizontal laser line crosses the halfway point
(D1/2), mark point P2).
8.
Measure the vertical distance between P1 and P2
(Figure
F
3
).
9.
If your measurement is greater than the Allowable
Distance Between P1 & P2 for the corresponding
Distance (D1) in the following table, the laser must be
serviced at an authorized service center.
Distance (D1)
Allowable Distance
Between P1 and P2
9 m (30’) 3 mm (1/8”)
12 m (40’) 4 mm (5/32”)
15 m (50’) 5 mm (7/32”)
Vertical Line Accuracy - Plumb
Checking the plumb of the laser’s vertical line.
1.
Measure the height of a door jamb (or a reference point on
the ceiling) to get height D1 (Figure
G
1
).
2.
Place the laser on the oor across from the door jam,
(Figure
G
1
).
3.
Slide the laser’s Power/Transport Lock switch to the right to
turn the laser ON (Figure
A
7
).
4.
Press twice to display a vertical line.
5.
Aim the laser’s vertical line toward the door jamb or the
reference point on the ceiling.
6.
Where the laser’s vertical line meets the height of the door
jam, mark point P1.
7.
From where the laser beam hits the oor, measure the D1
distance and mark it point P2.
8.
From P2, measure the D1 distance and mark it point P3.
9.
Move the laser to the opposite side of point P3 and aim the
laser’s vertical line toward point P2 (Figure
G
2
).
10.
Align the laser’s vertical line with points P2 and P3 on the
oor, and mark point P4 over the door jam.
11.
Measure the distance between P1 and P4 (Figure
G
3
).
… 10 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Stanley FMHT77598 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Stanley FMHT77598 in the language / languages: All languages as an attachment in your email.

The manual is 16,9 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info