Manual Stanley FMHT1-77438 (page 11 of 198) (All languages)

720740

Zoom out

Zoom in

1/198

Using the Laser with the Multibracket

Most line/dot lasers which have a 5/8-11 mounting thread can

be used with the Multibracket FMHT77435 (Figure

). The

multibracket can then be used free-standing or mounted in

several ways:

• Use its rubber strap around a pole, 2”x4”, or other vertical

object.

• Use its rear magnets against a metal beam.

• Hook its rear screw hole over a nail or screw on a wall.

• Use its ceiling clamp to hold onto the track for a hanging/

suspended ceiling.

• Use the bottom 5/8-11 or 1/4-20 thread to attach to a tripod.

Maintenance

• When the laser is not in use, clean the exterior parts with

a damp cloth, wipe the laser with a soft dry cloth to make

sure it is dry, and then store the laser in the kit box provided.

• Although the laser exterior is solvent resistant, NEVER use

solvents to clean the laser.

• Do not store the laser at temperatures below -20 ˚C (-5 ˚F ) or

above 60 ˚C (140 ˚F).

• To maintain the accuracy of your work, check the laser often

to make sure it is properly calibrated.

• Calibration checks and other maintenance repairs may be

performed by Stanley service centers.

Troubleshooting

The Laser Does Not Turn On

• If AA batteries are being used, make sure:

• Each battery is installed correctly, according to (+) and (–)

listed inside the battery compartment.

• The battery contacts are clean and free of rust or corrosion.

• The batteries are new, high-quality, name brand batteries

to reduce the chance of battery leakage.

• Make sure the AA batteries are in proper working condition. If

in doubt, try installing new batteries.

• When using rechargeable batteries, make sure the batteries

are fully charged.

• Be sure to keep the laser dry.

• If the laser unit is heated above 50 ˚C (120 ˚F), the unit will

not turn ON. If the laser has been stored in extremely hot

temperatures, allow it to cool. The laser level will not be

damaged by using the Power/Transport Lock switch before

cooling to its proper operating temperature.

The Laser Beams Flash

The lasers are designed to self-level up to an average of

4° in all directions. If the laser is tilted so much that the

internal mechanism cannot level itself, the laser beams will

ash indicating that the tilt range has been exceeded. THE

FLASHING BEAMS CREATED BY THE LASER ARE NOT

LEVEL OR PLUMB AND SHOULD NOT BE USED FOR

DETERMINING OR MARKING LEVEL OR PLUMB. Try

repositioning the laser on a more level surface.

The Laser Beams Will Not Stop Moving

The laser is a precision instrument. Therefore, if it is not

positioned on a stable (and motionless) surface, the laser will

continue to try to nd level. If the beam will not stop moving, try

placing the laser on a more stable surface. Also, try to make

sure that the surface is relatively at and level, so that the laser

is stable.

Service and Repairs

Note: Disassembling the laser level will void all warranties on

the product.

To assure product SAFETY and RELIABILITY, repairs,

maintenance and adjustment should be performed by

authorized service centers. Service or maintenance performed

by unqualied personnel may result in a risk of injury. To locate

your nearest Stanley service center, go to http://www.2helpU.

com.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Stanley FMHT1-77438 in the language / languages: All languages as an attachment in your email.

The manual is 16,28 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Stanley FMHT1-77438 Manual

Product: