720739
11
Zoom out
Zoom in
Previous page
1/198
Next page
11
GB
Using the Laser with the Multibracket
Most line/dot lasers which have a 5/8-11 mounting thread can
be used with the Multibracket FMHT77435 (Figure
I
). The
multibracket can then be used free-standing or mounted in
several ways:
Use its rubber strap around a pole, 2”x4”, or other vertical
object.
Use its rear magnets against a metal beam.
Hook its rear screw hole over a nail or screw on a wall.
Use its ceiling clamp to hold onto the track for a hanging/
suspended ceiling.
Use the bottom 5/8-11 or 1/4-20 thread to attach to a tripod.
Maintenance
When the laser is not in use, clean the exterior parts with
a damp cloth, wipe the laser with a soft dry cloth to make
sure it is dry, and then store the laser in the kit box provided.
Although the laser exterior is solvent resistant, NEVER use
solvents to clean the laser.
Do not store the laser at temperatures below -20 ˚C (-5 ˚F ) or
above 60 ˚C (140 ˚F).
To maintain the accuracy of your work, check the laser often
to make sure it is properly calibrated.
Calibration checks and other maintenance repairs may be
performed by Stanley service centers.
Troubleshooting
The Laser Does Not Turn On
If AA batteries are being used, make sure:
Each battery is installed correctly, according to (+) and (–)
listed inside the battery compartment.
The battery contacts are clean and free of rust or corrosion.
The batteries are new, high-quality, name brand batteries
to reduce the chance of battery leakage.
Make sure the AA batteries are in proper working condition. If
in doubt, try installing new batteries.
When using rechargeable batteries, make sure the batteries
are fully charged.
Be sure to keep the laser dry.
If the laser unit is heated above 50 ˚C (120 ˚F), the unit will
not turn ON. If the laser has been stored in extremely hot
temperatures, allow it to cool. The laser level will not be
damaged by using the Power/Transport Lock switch before
cooling to its proper operating temperature.
The Laser Beams Flash
The lasers are designed to self-level up to an average of
4° in all directions. If the laser is tilted so much that the
internal mechanism cannot level itself, the laser beams will
ash indicating that the tilt range has been exceeded. THE
FLASHING BEAMS CREATED BY THE LASER ARE NOT
LEVEL OR PLUMB AND SHOULD NOT BE USED FOR
DETERMINING OR MARKING LEVEL OR PLUMB. Try
repositioning the laser on a more level surface.
The Laser Beams Will Not Stop Moving
The laser is a precision instrument. Therefore, if it is not
positioned on a stable (and motionless) surface, the laser will
continue to try to nd level. If the beam will not stop moving, try
placing the laser on a more stable surface. Also, try to make
sure that the surface is relatively at and level, so that the laser
is stable.
Service and Repairs
Note: Disassembling the laser level will void all warranties on
the product.
To assure product SAFETY and RELIABILITY, repairs,
maintenance and adjustment should be performed by
authorized service centers. Service or maintenance performed
by unqualied personnel may result in a risk of injury. To locate
your nearest Stanley service center, go to http://www.2helpU.
com.
11


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Stanley FMHT1-77414 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Stanley FMHT1-77414 in the language / languages: All languages as an attachment in your email.

The manual is 16,28 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info