Manual Stanley FMEG220 (page 10 of 136) (English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish)

720759

Zoom out

Zoom in

1/136

ENGLISH

(Original instructions)

u NO EATING, DRINKING or SMOKING should be done

in the work area to prevent ingesting contaminated

paint particles. Workers should wash and clean up

BEFORE eating, drinking or smoking. Articles of food,

drink, or smoking should not be left in the work area

where dust would settle on them.

u Paint should be removed in such a manner as to

minimize the amount of dust generated.

u Areas where paint removal is occurring should be

sealed with plastic sheeting of 4 mils thickness.

u Sanding should be done in a manner to reduce tracking

of paint dust outside the work area.

u All surfaces in the work area should be vacuumed and

thoroughly cleaned daily for the duration of the sanding

project. Vacuum lter bags should be changed

frequently.

u Plastic drop cloths should be gathered up and disposed

of along with any dust chips or other removal debris.

They should be placed in sealed refuse receptacles

and disposed of through regular trash pick-up

procedures. During clean up, children and pregnant

women should be kept away from the immediate work

area.

u All toys, washable furniture and utensils used by

children should be washed thoroughly before being

used again.

Fitting and using wire brushes and wire wheels

Wire cup brushes or wire wheels screw directly on the grinder

spindle without the use of anges. b. A Type 27 guard is

required when using wire brushes and wheels. Wear work

gloves when handling wire brushes and wheels. They can

become sharp. Wheel or brush must not touch guard when

mounted or while in use. Undetectable damage could occur to

the accessory, causing wires to fragment from accessory

wheel or cup.

u Thread the wheel on the spindle by hand.

u Depress spindle lock button and use a wrench on the hub

of the wire wheel or brush to tighten the wheel.

u To remove the wheel, reverse the above procedure.

Warning! Failure to properly seat the wheel hub before

turning the tool on may result in damage to tool or wheel.

Wire wheels and brushes can be used for removing rust, scale

and paint, and for smoothing irregular surfaces.

Note: The same precautions should be taken when wire

brushing paint as when sanding paint.

u Allow the tool to reach full speed before touching the tool

to the work surface.

u Apply minimum pressure to work surface, allowing the tool

to operate at high speed. Material removal rate is greatest

when the tool operates at high speed.

u Maintain a 5˚ to 10˚ angle between the tool and work

surface for wire cup brushes as shown in gure I.

u Maintain contact between the edge of the wheel and the

work surface with wire wheels.

u Continuously move the tool in a forward and back motion

to avoid creating gouges in the work surface. Allowing the

tool to rest on the work surface without moving, or moving

the tool in a circular motion causes burning and swirling

marks on the work surface.

u Remove the tool from the work surface before turning the

tool off. Allow the tool to stop rotating before setting it

down.

Warning! Use extra care when working over an edge, as a

sudden sharp movement of grinder may be experienced.

Mounting and using cutting (type 41) wheels

Cutting wheels include diamond wheels and abrasive discs.

Abrasive cutting wheels for metal and concrete use are

available. Diamond blades for concrete cutting can

also be used.

NOTE: A closed, 2-sided Type 41 cutting wheel guard is sold

separately and is required when using cutting wheels. Failure

to use proper ange and guard can result in injury resulting

from wheel breakage and wheel contact.

Matching diameter backing ange and threaded clamp nut

(included with tool) must be used for cutting wheels.

Mounting closed (type 41) guard (Fig. J, K, L)

u Align the three lugs on the guard (7) with the three slots

on the hub. This will align the lugs with slots on the gear

case cover as shown in gure J.

u Push the guard down until the guard lug engages in the

groove on the gear case hub as shown in gure K.

u Rotate guard (7) counterclockwise to lock it into place. The

guard body should be positioned between the spindle and

the operator to provide maximum operator protection as

shown in gure L.

u Tighten the guard latch screw to secure the guard on the

gear case cover. You should be unable to rotate the guard

by hand. Do not operate grinder with a loose guard.

u To remove the guard, loosen the guard latch screw. Then

rotate the guard so that the three lugs on the guard (7)

align with the three slots on the hub and pull up on the

guard.

Mounting cutting wheels

u Place the unthreaded backing ange on spindle with the

raised section (pilot) facing up. The raised section (pilot)

on the backing ange will be against the wheel when the

wheel is installed.

u Place the wheel on the backing ange, centering the

wheel on the raised section (pilot).

u Install the threaded clamp nut with the raised section

(pilot) facing away from the wheel.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Stanley FMEG220 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 22,54 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Stanley FMEG220 Manual

Product: