Manual Stanley FMEG210 (page 7 of 136) (English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish)

720758

Zoom out

Zoom in

1/136

ENGLISH

(Original instructions)

The wheel may bind, walk up or kickback if the

power tool is restarted in the workpiece.

u Support panels or any oversized workpiece to

minimize the risk of wheel pinching and kickback.

Large workpieces tend to sag under their own weight.

Supports must be placed under the workpiece near the

line of cut and near the edge of the workpiece on both

sides of the wheel.

u Use extra caution when making a "pocket cut" into

existing walls or other blind areas. The protruding

wheel may cut gas or water pipes, electrical wiring or

objects that can cause kickback.

Safety warnings specic for sanding operations

u Do not use excessively oversized sanding disc paper.

Follow manufacturers recommendations, when

selecting sanding paper. Larger sanding paper

extending beyond the sanding pad presents a laceration

hazard and may cause snagging, tearing of the disc or

kickback.

Safety warnings specic for wire brushing

operations

u Be aware that wire bristles are thrown by the brush

even during ordinary operation.

Do not overstress the wires by applying excessive

load to the brush. The wire bristles can easily penetrate

light clothing and/or skin.

u If the use of a guard is recommended for wire

brushing, do not allow any interference of the wire

wheel or brush with the guard. Wire wheel or brush may

expand in diameter due to work load and centrifugal

forces.

Safety of others

u This appliance is not intended for use by persons

(including children) with reduced physical, sensory or

mental capabilities, or lack of experience and knowledge,

unless they have been given supervision or instruction

concerning use of the appliance by a person responsible

for their safety.

u Children should be supervised to ensure that they do not

play with the appliance.

Residual risks

Additional residual risks may arise when using the tool which

may not be included in the enclosed safety warnings.

These risks can arise from misuse, prolonged use etc.

Even with the application of the relevant safety regulations

and the implementation of safety devices, certain residual

risks can not be avoided. These include:

u Injuries caused by touching any rotating/moving parts.

u Injuries caused when changing any parts, blades or

accessories.

u Injuries caused by prolonged use of a tool. When using

any tool for prolonged periods ensure you take regular

breaks.

u Impairment of hearing.

u Health hazards caused by breathing dust developed when

using your tool (example:- working with wood, especially

oak, beech and MDF.)

Vibration

The declared vibration emission values stated in the technical

data and the declaration of conformity have been measured

in accordance with a standard test method provided by

EN 60745 and may be used for comparing one tool with

another. The declared vibration emission value may also be

used in a preliminary assessment of exposure.

Warning! The vibration emission value during actual use of

the power tool can differ from the declared value depending

on the ways in which the tool is used. The vibration level may

increase above the level stated.

When assessing vibration exposure to determine safety

measures required by 2002/44/EC to protect persons regularly

using power tools in employment, an estimation of vibration

exposure should consider, the actual conditions of use and the

way the tool is used, including taking account of all parts of

the operating cycle such as the times when the tool is

switched off and when it is running idle in addition to the

trigger time.

Labels on tool

The following pictograms, along with the date code, are shown

on the tool:

Warning! To reduce the risk of injury, the user

must read the instruction manual.

Wear safety glasses or goggles when operating

this tool.

Wear ear protection when operating this tool

Electrical safety

Your charger is double insulated; therefore no

earth wire is required. Always check that the

mains voltage corresponds to the voltage on the

rating plate.

u If the supply cord is damaged, it must be replaced by the

manufacturer or an authorised Stanley Fat Max Service

Centre in order to avoid a hazard.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Stanley FMEG210 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 22,54 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Stanley FMEG210 Manual

Product: