622174
13
Zoom out
Zoom in
Previous page
1/152
Next page
13
ENGLISH
(Original instructions)
Crown moulding cut (g. L)
Crown moulding can only be cut at on the table with this
mitre saw.
u This mitre saw has special mitre stops on 31.6° left and
right and a bevel stop of 33.9° for special crown moulding,
i.e. 52° between the back of the moulding and the top
at surface that ts against the ceiling; 38° between the
back of the moulding and the bottom at surface that ts
against the wall.
u Refer to the following table to make this crown moulding
cut:
Settings Left side Right side
Inside
corner
Mitre
angle
Right 31.6 º Left 31.6 º
Bevel
angle
33.9 º 33.9 º
Moulding
position
Top against fence Bottom against fence
Finished
side
Keep left side of cut Keep left side of cut
Outside
corner
Mitre
angle
Right 31.6 º Left 31.6 º
Bevel
angle
33.9 º 33.9 º
Moulding
position
Bottom against fence Top against fence
Finished
side
Keep right side of cut Keep right side of cut
Note: These special stops can not be used with 45° crown
moulding.
Note: Since most rooms do not have angles of exactly 90°,
ne tuning is needed, always make a test cut to conrm the
correct angles.
Setting the cutting depth (g. M)
The depth of cut can be preset for even and repetitive shallow
cuts.
u Adjust the cutting head down until the teeth of the blade
are at the required depth of cut.
u While holding the upper arm in position, turn the stop knob
(47) until it touches the stop plate (49).
u Check the blade depth by moving the cutting head front
to back through the full motion of a typical cut along the
control arm.
Carrying the tool (g. N)
u Loosen the mitre detent lever (11) (g. B) and turn the
table all the way to the right. Lock the table at the 45°
mitre angle.
u Pull the cutting head to the front of the saw and lock the
carriage with the lock knob (48) (g. J).
u Lower the cutting head and push in the lock pin (46) (g.
H).
u Carry the mitre saw with the front and the rear carrying
handles (24, 27).
Warning! Do not carry the machine by the guard.
Blade and tooth type
Material
Tooth type
600 ~ 100T 24 ~ 100T
TCG ATB
Wood
Lumber
Plywood
Hardwood
Chipboard
Plastic
PVC
ABS
Acrylic
PC
PS
Non-ferrous
metal
Aluminium
Copper
Your mitre saw has been supplied with a negative rake saw
blade. It is advisable to use a negative rake saw blade.
u TCG type - For cutting aluminium sheets, tubing extru-
sions and other non-ferrous metals such as copper, brass.
u ATB type - For general cutting and trimming of wood,
plywood, and sizing pressboard, hardboard, and particle
board, when a neat cut is needed.
Always use a negative rake blade when cutting non-ferrous
metals.
Warning! Do not use any blade that requires a spacer or
spindle ring to t. Only use blades as specied in this manual.
13


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Stanley FME720 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Stanley FME720 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 9,13 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info