Manual Stanley FME720 (page 10 of 152) (English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish)

622174

Zoom out

Zoom in

1/152

ENGLISH

(Original instructions)

Features

This tool includes some or all of the following features.

1. Laser on/off switch

2. Main operating handle

3. On/off switch

4. Motor housing

5. Moveable lower guard

6. Table extension material stop (right)

7. Table extension (right)

8. Kerf plate

9. Mitre clamp

10. Mitre lock knob

11. Mitre detent lever

12. Mitre position adjustment pointer

13. Mitre scale

14. Rotating table

15. Bench mounting holes

16. Clamp locating mounts

17. Table extension (left)

18. Table extension material stop (left)

19. Table extension securing knob

20. High sliding fence clamp

21. Left-hand fence

22. Left-hand high sliding fence

23. 33.9° bevel pin

24. Rear carry handle

25. Saw dust outlet

26. Metal upper guard

27. Front carry handle

28. Removable brush box

29. Carriage

30. Bevel lock handle

31. Bevel scale

32. Right-hand fence

33. Laser

34. Saw blade

35. Spindle lock button

36. Saw arm release lever

Fig. R

53. Clamp

Assembly

Warning! Before assembly, make sure that the tool is

switched off and unplugged.

Note: This tool is accurately adjusted before shipping from

the factory. Check the following accuracy and readjust them if

necessary in order to obtain the best results in operation

Laser beam

The laser beam alignment is set at manufacturing source and

is not user adjustable.

Mitre angle adjustment

The sliding compound mitre saw scale can be easily read

showing mitre angles from 0° to 47° to the left and the right.

The most common angle cut setting slots have positive stops,

permitting fast adjustments to the required position. Follow the

process below for quickest and most accurate adjustments.

Mitre clamp (g. B)

The mitre clamp (9) allows the saw to be set to specic angles

other than the preset angles of 0°, 15°, 22.5°, 31.6°, and 47°

which are set using the mitre detent lever (11).

Adjusting the bevel stops at 90° and 45° (g. C - F)

u Loosen the bevel lock handle (30) and move the cutting

head all the way to the right and tighten the bevel lock

handle.

u Use a square to set the blade at 90° to the table (g. D).

u If an adjustment is necessary, loosen the lock nut (41) and

adjust the bolt (40) with the wrench so that the blade is

90° to the table.

u Tighten the lock nut (41).

u Align the bevel indicator (39) with the 0° mark by adjusting

the screw (38).

When adjusting the 45° stop, make sure that the left-hand

high sliding fence (22) is adjusted so that the cutting head can

be moved to the 45° position (g. E).

u Release the high sliding fence clamp (20) and move the

high sliding fence (22) away from the blade.

u Tighten the high sliding fence clamp (20).

u Pull out the 33.9° bevel pin (23) and follow the same

procedures for the 90° but move the cutting head to the

left and use the lock nut (43) and adjustment bolt (42).

Adjusting the fence (g. G - H)

u Lower the cutting head and push in the lock pin (46).

Make sure that the table is in 0° mitre position.

u Place a combination square against the left-hand fence

(21) and next to the saw blade (34) (g. G).

u If the blade does not contact the square along it’s length,

loosen the three screws (44) (g. H) and adjust the fence.

u Tighten the three screws (44).

Bench mounting (g. I)

Note: We highly recommend that you bolt this mitre saw

securely to a work bench to gain the maximum stability of

your machine. Make sure that the machine is xed to a bench

whenever possible.

u Locate and mark the four bolt holes on the bench.

u Drill the bench with an Ø10 mm drill bit.

u Bolt the mitre saw onto the bench with bolts, washers and

nuts.

Note: These fasteners are not supplied with the tool.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Stanley FME720 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 9,13 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Stanley FME720 Manual

Product: