622604
7
Zoom out
Zoom in
Previous page
1/88
Next page
7
ENGLISH
(Original instructions)
Carbide grout removal blade.
(Part number - STA26125-XJ)
Carbide coated surface ideal for
clearing grout and tile adhesive from
at surfaces and for fast stock
removal of wood, chipboard and
breglass.
Carbide rasp.
(Part number - STA26130-XJ)
Carbide coated surface ideal for grout
removal and for fast stock removal of
plastics, chipboard and breglass.
Sanding Sheets.
(Part number - STA32348-XJ)
Various grades for sanding of wood,
painted and varnished surfaces.
Assembly
Fitting and removing the accessories (g. A - F)
Warning! Before tting an accessory, disconnect the tool from
the mains supply.
Fitting a Stanley Fat Max accessory (g. A - C)
u Hold the tool and squeeze the accessory clamping lever
(3).
u Slide the accessory (8) between the shaft and the acces-
sory holder making sure the accessory engages all eight
pins on the holder and is ush with the shaft.
u Release the accessory clamping lever.
Note: Some accessories, such as scrapers and blades can be
mounted at an angle if required (g. C).
Removing a Stanley Fat Max accessory accessory (g. A)
u Hold the tool and squeeze the accessory clamping lever
(3).
u Pull the accessory from the tool making sure the acces-
sory dis-engages from all eight pins on the holder.
u Release the accessory clamping lever.
Warning: Gloves must be worn when removing accessories
as then may become hot during use.
Fitting a sanding sheet (g. D)
u Line up the sanding sheet (9) with the sanding base (4) as
shown.
u Press the sheet rmly and evenly onto the sanding base,
making sure that the holes in the sheet coincide with the
holes in the base.
Removing a sanding sheet
u Pull the sanding sheet off the sanding base (4).
Warning! Never use the sanding base without a sanding
sheet or accessory in place.
Fitting the dust extraction adaptor (g. E)
u Line up the dust extraction adaptor (5) with the sanding
base (4) as shown.
u Press the adaptor rmly and evenly in to the sanding
base.
u Secure the adaptor by turning the locking nut (12) clock-
wise.
u Connect a vacuum cleaner to the dust extraction adaptor.
Removing the dust extraction adaptor
u Turn the locking nut (12) anti-clockwise.
u Pull the dust extraction adaptor (5) out of the sanding
base (4).
Fitting alternative accessories (g. F)
u Place the spacer (6) onto the collar (10).
u Place the alternative accessory (11) onto the collar (10).
u Firmly attach the xing bolt (7) into place to ensure a tight
t for the alternative accessory (11).
Note: The spacer and xing bolt are not used to attach
Stanley Fat Max accessories. Black and decker accessories
are attached using the Super-lok
TM
Tool free accessory clamp-
ing lever.
Use
Warning! Let the tool work at its own pace. Do not overload.
Warning! Before cutting into walls, oors or ceilings, check for
the location of wiring and pipes.
Variable speed control (g. G)
The variable speed control allows you to adapt the speed of
the tool to the application.
u Set the variable speed dial (2) to the desired setting. At
setting 1 the tool will operate at low speed, 10,000 min-1.
At setting 6 the tool will operate at the maximum speed,
20,000 min-1.
Switching on and off (g. H)
u To switch the tool on, slide the on/off switch (1) forward
(position I).
u To switch the tool off, slide the on/off switch (1) to the rear
(position O).
7


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Stanley FME600 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Stanley FME600 in the language / languages: All languages as an attachment in your email.

The manual is 8,59 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info