Manual Stanley FME380 (page 11 of 104) (English, German, Dutch, Danish, French, Italian, Portuguese, Spanish, Norwegian, Finnish)

720791

Zoom out

Zoom in

1/104

ENGLISH

(Original instructions)

Use

Warning! Let the tool work at its own pace. Do not overload.

Switching on and off (g. A)

Note:Before engaging the on/off switch, check the saw blade

to see if it is tted properly and runs smoothly, and the blade

clamp screw is well tightened.

u Push the trigger lock and shoe release button button (10)

to release the trigger.

u Switch on tool by pulling trigger switch (1).

u Switch off tool by releasing trigger switch (1).

Adjusting cutting depth (0-28,5 mm) (g.B)

u Loosen clamp (3).

u Set desired cutting depth using scale (2).

u Tighten clamp (3)

u For an optimal quality cut, the saw blade should not

extend more than 3 mm below the workpiece

u Be aware that the actual depth of cut of the diamond

disc differs approx. 2 mm from the depth of cut indicated

on scale (2).

Note: Always make trial cuts rst to verify actual line of

cut.

Dust suction (g.C)

u connect vacuum cleaner hose (19) to connection (13) and

vacuum cleaner as illustrated.

Warning! Never let the vacuum cleaner hose interfere with

the lower guard or the cutting operation.

Warning! Do not use vacuum cleaner when cutting metal.

Changing saw blade (g. D - G)

Warning! Before changing blades or performing any mainte-

nance, ensure the tool is off and disconnected from the power

source.

u Set cutting depth to the maximum (g. D).

u Use hex key (15) provided.

u Push spindle-lock button (14) and hold (Fig. E).

Remove blade bolt (9) by turning hex key (15)

CLOCKWISE (= in same direction as arrow imprinted on

the guard) (Fig. F).

u Release spindle-lock button (14).

u Remove ange (8).

u Press button (10) with your thumb

u Lift up foot (7) and remove saw blade.

u Install new blade making sure that rotation of blade is in

same direction as arrow imprinted on the guard.

u Mount ange (8).

u Firmly tighten blade bolt (9) by turning hex key (15)

COUNTER-CLOCKWISE while pushing spindle-lock

button (14).

u Release spindle-lock button (14).

Operating the tool (g. H - M)

u Set desired cutting depth.

u Connect plug to power source.

u Press button (10) with your thumb.

u Place tool with front end of foot flat on workpiece.

u Tilt tool forward with line-of-cut indicator (20) lined up with

desired line of cut marked on the workpiece (g. H).

u Ensure that the saw teeth are not engaged into the work-

piece.

u Switch on the tool.

u The tool should run at full speed before the blade enters

into the workpiece.

u Do not force the tool (apply light and continuous

pressure in order to avoid overheating the blade tips and,

in case of cutting plastics, melting the plastic material).

u While working, always hold the tool at the insulated grip

area(s).

u After completing the cut switch off tool by releasing trigger

(1).

u Ensure that the blade has come to a complete standstill,

before you lift the tool from the workpiece.

Electronic Function. Laser beam action (Fig.I)

Caution! When not in use, be sure to turn off the laser.

Never look into the laser beam directly; laser beam may injure

your eyes.

LASER RADIATION: DO NOT STARE INTO THE BEAM or

any CLASSII LASER PRODUCTS.

Before shifting the laser line or performing maintenance

adjustment, be sure to unplug the tool.

u To turn the laser on/off, toggle the switch (12a) on the

back of the laser housing.

Cleaning of the lens for the laser light

If the lens for the laser light becomes dirty, or sawdust ad-

heres to it in such a way that the laser line is no longer easily

visible, unplug the saw and clean the lens carefully with a

damp, soft cloth. Do not use solvents or any petroleum based

cleaners on the lens.

Note: When laser line is dim and almost or entirely invisible

because of the direct sunlight in the indoor or outdoor window

near your work area, relocate the work area to a place not

exposed to direct sunlight.

Note: All of the adjustments for the operation of this machine

have been carried out at the factory.

Caution: Use of controls or adjustments or performance of

procedures other than those specied herein may result in

hazardous radiation exposure. The use of optical instruments

with this product will increase eye hazard. Do not attempt to

repair or disassemble the laser. If unqualied persons attempt

to repair this laser product, serious injury may result.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Stanley FME380 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 6,72 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Stanley FME380 Manual

Product: