Manual Stanley FME380 (page 8 of 104) (English, German, Dutch, Danish, French, Italian, Portuguese, Spanish, Norwegian, Finnish)

720791

Zoom out

Zoom in

1/104

ENGLISH

(Original instructions)

d. Store idle power tools out of the reach of children and

do not allow persons unfamiliar with the power tool or

these instructions to operate the power tool. Power

tools are dangerous in the hands of untrained users.

e. Maintain power tools. Check for misalignment or

binding of moving parts, breakage of parts and any

other condition that may affect the power tools

operation. If damaged, have the power tool repaired

before use. Many accidents are caused by poorly

maintained power tools.

f. Keep cutting tools sharp and clean. Properly

maintained cutting tools with sharp cutting edges are less

likely to bind and are easier to control.

g. Use the power tool, accessories and tool bits etc. in

accordance with these instructions, taking into

account the working conditions and the work to be

performed. Use of the power tool for operations different

from those intended could result in a hazardous situation.

5. Service

a. Have your power tool serviced by a qualied repair

person using only identical replacement parts. This

will ensure that the safety of the power tool is maintained.

Safety instructions for all saws

Cutting procedures

Danger: Keep hands away from cutting area

and the blade. Keep your second hand on

auxiliary handle, or motor housing. If both

hands are holding the saw, they cannot be cut

by the blade

u Do not reach underneath the workpiece. The guard

cannot protect you from the blade below the workpiece.

u Adjust the cutting depth to the thickness of the work-

piece. Less than a full tooth of the blade teeth should be

visible below the workpiece.

u Never hold piece being cut in your hands or across

your leg. Secure the workpiece to a stable platform. It

is important to support the work properly to minimize body

exposure, blade binding, or loss of control.

u Hold power tool by insulated gripping surfaces when

performing an operation where the cutting accessory

may contact hidden wiring or its own cord. Cutting ac-

cessory contacting a "live" wire may make exposed metal

parts of the power tool "live" and could give the operator

an electric shock

u When ripping, always use a rip fence or straight edge

guide. This improves the accuracy of cut and reduces the

chance of blade binding.

u Always use blades with correct size and shape (dia-

mond versus round) of arbour holes.

Blades that do not match the mounting hardware of the

saw will run eccentrically, causing loss of control.

u Never use damaged or incorrect blade washers or

bolt. The blade washers and bolt were specially designed

for your saw, for optimum performance and safety of

operation.

Warning! Contact with or inhalation of dusts

arising from sawing applications may endanger

the health of the operator and possible bystand-

ers. Wear a dust mask specically designed for

protection against dust and fumes and ensure

that persons within or entering the work area are

also protected.

u Thoroughly remove all dust after sawing.

u Do not let children or pregnant women enter the work

area.

u Do not eat, drink or smoke in the work area.

u Dispose of dust particles and any other debris safely.

u The intended use is described in this instruction manual.

The use of any accessory or attachment or performance

of any operation with this tool other than those recom-

mended in this instruction manual may present a risk of

personal injury and/or damage to property.

u The accessory will continue to move after releasing the

switch. Always switch the tool off and wait for the acces-

sory to come to a complete standstill before putting the

tool down.

u Keep blades sharp. Dull or damaged blades may cause

the saw to swerve or stall under pressure. Always use the

appropriate type of saw blade for the workpiece material

and type of cut.

u When cutting pipe or conduit, make sure that they are free

from water, electrical wiring, etc.

u Do not touch the workpiece or the blade immediately after

operating the tool. They can become very hot.

u Be aware of hidden hazards, before cutting into walls,

oors or ceilings, check for the location of wiring and

pipes.

u Avoid cutting nails, inspect the material that is being cut to

see if there are nails in it and remove before cutting.

u Do not run the saw while carrying it at your side.

u Make sure the depth locking lever is tight and secure

before making a cut.

u When cutting is interrupted or the blade bound, please

release the trigger immediately and hold the saw rmly

in the material until the blade comes to a complete stop.

Never attempt to remove the saw from the work or pull

the saw backward while the blade is in motion, otherwise,

kickback might happen.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Stanley FME380 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 6,72 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Stanley FME380 Manual

Product: