720690

Stanley FME360 Manual

7
Zoom out
Zoom in
Previous page
1/72
Next page
English
7
(original instructions)
● Turn the saw upside down so you are as close to the work
surface as possible.
Sawing metal
Be aware that sawing metal takes much more time than
sawing wood.
● Use a saw blade suitable for sawing metal. Use a ne-
tooth saw blade for ferrous metals and a coarser saw
blade for non-ferrous metals.
● When cutting thin sheet metal, clamp a piece of scrap
wood to the back surface of the workpiece and cut
through this sandwich.
● Spread a lm of oil along the intended line of cut.
Pocket cutting in wood
● Measure and mark the required pocket cut.
● Fit a saw blade suitable for pocket cutting.
● Rest the shoe (4) on the workpiece in such a position that
the blade forms an appropriate angle for the pocket cut.
● Switch on the tool and slowly feed the blade into the
workpiece. Make sure that the shoe (4) remains in contact
with the workpiece at all times.
Cutting branches
Branches up to 25 mm in diameter can be cut with this tool.
@
Warning! Do not use the tool while in a tree, on a
ladder or on any other unstable surface. Be aware of
where the branch will fall.
● Cut downward and away from your body.
● Make the cut close to the main branch or tree body.
Vertical cutting
The tool allows close cutting to corners and other
difcult areas.
● Insert the shank of the saw blade into the blade holder
with the teeth of the blade facing upward.
● Hold the tool with the shoe (1) facing downward so that
you are as close to the work surface as possible.
● Cut forward and away from your body.
Accessories
The performance of your tool depends on the accessory used.
STANLEY FATMAX accessories are engineered to high quality
standards and designed to enhance the performance of your
tool. By using these accessories you will get the very best
from your tool.
Blades
The saw will accept a blade up to 305 mm long. Always use
the shortest blade suitable for your project but long enough to
keep the blade cutting through the material. Longer blades are
more likely to be bent or damaged during use. During
operation some longer blades may vibrate or shake if the saw
is not kept in contact with the workpiece
Maintenance
Your STANLEY FATMAX tool has been designed to operate
over a long period of time with a minimum of maintenance.
Continuous satisfactory operation depends upon proper tool
care and regular cleaning.
@
Warning! Before performing any maintenance on
the tool, unplug the tool. Unplug the charger before
cleaning it.
● Regularly clean the ventilation slots in your tool using a
soft brush or dry cloth.
● Regularly clean the motor housing using a damp cloth. Do
not use any abrasive or solvent-based cleaner.
Mains plug replacement (U.K. & Ireland only)
If a new mains plug needs to be tted:
● Safely dispose of the old plug.
● Connect the brown lead to the live terminal in the
new plug.
● Connect the blue lead to the neutral terminal.
@
Warning! No connection is to be made to the earth
terminal. Follow the tting instructions supplied with
good quality plugs. Recommended fuse: 10 A.
Protecting the environment
Z
Separate collection. Products and batteries
marked with this symbol must not be disposed of
with normal household waste.
Products and batteries contain materials that can be
recovered or recycled, reducing demand for raw materials.
Please recycle electrical products and batteries according
to local provisions. Further information is available at
www.2helpU.com
Technical data
FME360 (Type 1)
Input voltage
V
ac
230
Power input
W
900
No-load speed (SPM)
min
-1
0 - 3,200
Max. blade length
mm 305
Weight
kg
3.5
L
pA
(sound pressure) 92.5 dB(A), Uncertainty (K) 5 dB(A)
L
WA
(sound power) 103.5 dB(A), Uncertainty (K) 5 dB(A)
Vibration total values (triax vector sum) according to EN62841:
Cutting board with original blade (a
h, B
) 22.5 m/s
2
, uncertainty (K) 1.5 m/s
2
Cutting wooden beam with original blade
(a
h, WB
) 22.1 m/s
2
, uncertainty (K) 1.5 m/s
2
… 7 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Stanley FME360 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Stanley FME360 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 2,45 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info