622139

Stanley FME140 Manual

5
Zoom out
Zoom in
Previous page
1/72
Next page
5
ENGLISH
(Original instructions)
When assessing vibration exposure to determine safety
measures required by 2002/44/EC to protect persons regularly
using power tools in employment, an estimation of vibration
exposure should consider, the actual conditions of use and the
way the tool is used, including taking account of all parts of the
operating cycle such as the times when the tool is switched off
and when it is running idle in addition to the trigger time.
Labels on tool
The following pictograms are shown on the tool:
:
Warning! To reduce the risk of injury, the user must
read the instruction manual.
Electrical safety
#
This tool is double insulated; therefore no earth wire
is required. Always check that the power supply
corresponds to the voltage on the rating plate.
u If the supply cord is damaged, it must be replaced by the
manufacturer or an authorised Stanley Fat Max Service
Centre in order to avoid a hazard.
Features
This tool includes some or all of the following features.
1. Variable speed switch
2. Lock-on button
3. Variable speed control knob
4. Forward/reverse switch
5. Drilling mode selector
6. Chuck
7. Depth stop
8. Side handle
Assembly
Warning! Before assembly, make sure that the tool is
switched off and unplugged.
Fitting the side handle and depth stop (g. A)
u Turn the grip counterclockwise until you can slide the side
handle (8) onto the front of the tool.
u Rotate the side handle into the desired position.
u Insert the depth stop (7) into the mounting hole as shown.
u Set the drilling depth as described below.
u Tighten the side handle by turning the grip clockwise.
Setting the drilling depth (g. A)
u Slacken the side handle (8) by turning the grip counter-
clockwise.
u Set the depth stop (7) to the desired position. The maxi-
mum drilling depth is equal to the distance between the tip
of the drill bit and the front end of the depth stop.
u Tighten the side handle by turning the grip clockwise.
Fitting an accessory (g. B)
u Open the chuck by turning the sleeve (9) counterclock-
wise.
u Insert the bit shaft (10) into the chuck.
u Tighten the chuck by turning the sleeve clockwise.
Use
Warning! Let the tool work at its own pace. Do not overload.
Warning! Before drilling into walls, oors or ceilings, check for
the location of wiring and pipes.
Selecting the drilling mode
u For hammer drilling in masonry and concrete, set the
operating mode selector (5) to the
s
position
u For drilling in steel, wood and plastics, set the operating
mode selector (5) to the
r
position.
Selecting the direction of rotation
For drilling and tightening screws, use forward (clockwise)
rotation. For loosening screws or removing a jammed drill bit,
use reverse (counterclockwise) rotation.
u To select forward rotation, push the forward/reverse slider
(4) to the left.
u To select reverse rotation, push the forward/reverse slider
to the right.
Warning! Never change the direction of rotation while the
motor is running.
Switching on and off
u To switch the tool on, press the variable speed switch (1).
The tool speed depends on how far you press the switch.
If the tool has a variable speed control knob (3), set it
to the required speed range. As a general rule, use low
speeds for large diameter drill bits and high speeds for
smaller diameter drill bits.
u For continuous operation, press the lock-on button (2) and
release the variable speed switch. This option is available
only at full speed or at any speed preset with the variable
speed control knob (3). This option does not work in
reverse rotation.
u To switch the tool off, release the variable speed switch.
To switch the tool off when in continuous operation, press
the variable speed switch once more and release it.
… 5 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Stanley FME140 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Stanley FME140 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 1,95 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info