720682
13
Zoom out
Zoom in
Previous page
1/186
Next page
13
ENGLISH
(Original instructions)
Features
This tool includes some or all of the following features.
1. Trigger switch
2. Operating handle
3. Mounting holes
4. Lower Guard
5. Mitre locking knob
6. Mitre latch button
7. Kerf plate
8. Mitre scale
9. Mitre scale indicator
10. Carry grips
11. Fence
12. Bevel lock knob
13. Rails
13a.Velcro strap
14. Dust port
15. Battery pack
16. Work light switch
17. Lock off lever
18. Rail lock screw
19. Clamp mounting hole
20. Lock down pin
Assembly (Fig. A)
Your mitre saw is part assembled in the carton.
uOpen the box and lift the saw out by using the carry grips
(10) in the base of the saw (Fig. A).
u Place the saw on a smooth, at surface such as a work-
bench or strong table.
u Examine Assembly diagram on page 2 of this manual to
become familiar with the saw and its various parts. The
section on adjustments will refer to these terms and you
must know what and where the parts are.
u The mitre locking knob (5) is not assembled for shipping.
Remove the mitre locking knob (5) from the packaging
and screw onto the saw, see gure G and J for position.
u Your saw has a built-in dust port (14) that allows either
the supplied, but not assembled, dust bag (35) or shop
vacuum system to be connected (Fig. N).
Kerf plate (Fig. J)
The kerf plate (7) is mounted to the table by 6 screws. The
kerf plate (7) height is not adjustable.
Note: If the kerf plate (7) is worn, damaged or needs to be
replaced, repairs should be carried out by authorised repair
agents or Stanley Fat Max service staff.
Lock down pin (Fig. F)
Warning! The lock down pin should be used ONLY when
carrying or storing the saw. NEVER use the lock down pin for
any cutting operation.
Note: To lift, carry and support the mitre saw during transport
use the two carrying handles (10) located on both sides of the
mitre saw base (Fig. A).
To lock the saw head in the down position, push the saw head
down, push the lock down pin (20) in and release the saw
head. This will hold the saw head safely down for transporting
the saw from place to place. To release, press the saw head
down and pull the pin out.
Warning! Always be sure that the tool is switched off and the
battery is removed from the tool before adjusting or checking
the tools function.
Charging a battery (g. B)
Stanley FatMax chargers are designed to charge Stanley
FatMax battery packs.
u Plug the charger (21) into an appropriate outlet before
inserting a battery pack (15).
u Insert the battery pack (15) into the charger, making sure
the battery pack is fully seated in the battery slots
(Figure B).
The LED (21a) will ash indicating that the
battery is being charged.
The completion of charge is indicated by the
LED remaining on continuously. The pack is
fully charged and may be used at this time or
left in the charger.
u Recharge discharged batteries as soon as possible after
use or battery life may be greatly diminished.
u For longest battery life, do not discharge batteries fully.
It is recommended that the batteries be recharged after
each use.
Charger diagnostics (g. C)
This charger is designed to detect certain problems that can
arise with the battery packs or the power source. Problems
are indicated by one LED ashing in different patterns.
Bad battery
The charger can detect a weak or damaged
battery. The LED ashes in the pattern indi-
cated on the label. If you see this bad battery
blink pattern, do not continue to charge the battery. Return it
to a service centre or a collection site for recycling.
Hot/cold pack delay
When the charger detects a battery that
is excessively hot or excessively cold, it
automatically starts a Hot/Cold Pack Delay,
suspending charging until the battery has normalized. After
this happens, the charger automatically switches to the Pack
13


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Stanley FMCS701 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Stanley FMCS701 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 11,87 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info