721834
5
Zoom out
Zoom in
Previous page
1/68
Next page
5
ENGLISH
(Original instructions)
5. Tank latch
6. Intake port
7. Battery port
8. Vacuum hose
9. Hose clip
10 . Side exhaust port
11. Crevice tool
12. Wide nozzle tool
Assembly
Attaching vacuum hose (Fig. A)
The vacuum hose (8) will need to be attached to the
vacuum before using the appliance.
u Place the vacuum on a at, rm surface.
u Unlatch tank latches (5) and remove power head from
the tank. Remove the hose (8) from the tank.
u Align the hose end (13) with the intake port (6) on the
front of the appliance, ensuring the hose alignment lock
(14) is aligned with the arrow (15) on the intake port.
u Insert the hose end into the intake port and twist
clockwise to lock in place.
u Replace power head onto the tank and secure latches.
Note: The power head will only t onto the tank when the
intake port on the front of the power head and the storage
area for the wide nozzle tool on the tank are aligned as
shown in gure A.
Charging the battery (not supplied)
The battery needs to be charged before rst use and whenev-
er it fails to produce sufcient power on jobs that were easily
done before. The battery may become warm while charging;
this is normal and does not indicate a problem.
Warning! Do not charge the battery at ambient temperatures
below 10 °C or above 40 °C. Recommended charging tem-
perature: approx. 24 °C.
Note: The charger will not charge a battery if the cell tempera-
ture is below approximately 10 °C or above 40 °C.
The battery should be left in the charger and the charger
will begin to charge automatically when the cell temperature
warms up or cools down.
u To charge the battery (16), insert it into the charger. The
battery will only t into the charger in one way. Do not
force. Be sure that the battery is fully seated in the charg-
er.
u Plug in the charger and switch on at the mains.
The charging indicator will ash continuously (slowly).
The charge is complete when the charging indicator lights
continuously. The charger and the battery can be left connect-
ed indenitely with the LED illuminated. The LED will change
to ashing (charging) state as the charger occasionally tops
up the battery charge.
The charging indicator will be lit as long as the battery is
connected to the plugged-in charger.
u Charge discharged batteries within 1 week. Battery life will
be greatly diminished if stored in a discharged state.
Leaving the battery in the charger
The charger and battery pack can be left connected with the
LED glowing indenitely. The charger will keep the battery
pack fresh and fully charged.
Charger diagnostics
If the charger detects a weak or damaged battery, the charg-
ing indicator will ash red at a fast rate. Proceed as follows:
u Re-insert the battery (16).
u If the charging indicators continues ashing at a fast rate,
use a different battery to determine if the charging process
works properly.
u If the replaced battery charges correctly, the original
battery is defective and should be returned to a service
centre for recycling.
u If the new battery gives the same indication as the original
battery, take the charger to be tested at an authorised
service centre.
Note: It may take as long as 60 minutes to determine that
the battery is defective. If the battery is too hot or too cold,
the LED will alternately blink, fast and slow, one ash at each
speed and repeat.
Installing and removing the battery pack (not
supplied) (Fig. B)
Warning! Ensure battery port and terminals are dry and clean
before installing battery pack.
u To install the battery pack (16) into the power head, align
the battery pack with the rails inside the tool’s battery port
(7) until the battery pack is rmly seated in the tool and
ensure that it does not disengage.
u To remove the battery pack from the tool, press the
release button (17) and rmly pull the battery pack out of
the tool handle. Insert it into the charger as described in
the charger section of this manual.
Correct hand position
Warning! To reduce the risk of serious personal injury,
ALWAYS hold securely in anticipation of a sudden reaction.
u Proper hand position requires one hand on the main
handle (2).
Use
On / Off Switch (Fig. C)
u Attach the appropriate accessory to the hose (8).
u Insert battery pack.
5


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Stanley FMC795B at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Stanley FMC795B in the language / languages: All languages as an attachment in your email.

The manual is 2,11 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info