622595
9
Zoom out
Zoom in
Previous page
1/172
Next page
9
ENGLISH
(Original instructions)
Accessories
The tool is supplied with a guard intended for grinding pur-
poses only. If the unit is intended to perform cutting off opera-
tions, a guard (24, Fig H) specic for this operation must be
tted. A suitable guard for cutting off operations part number
1004683-29 is available and can be obtained from Stanley
Fat Max service centres. Further information for guard types
and accessories is available in the Grinding and cutting chart
which can be found at the back of this language section.
The performance of your tool depends on the accessory used.
Stanley Fat Max accessories are engineered to high quality
standards and designed to enhance the performance of your
tool. By using these accessories you will get the very best
from your tool.
Assembly
Warning! Before assembly, remove the battery from the tool.
Fitting and removing the guard (g. B)
The tool is supplied with a guard intended for grinding pur-
poses only. If the unit is intended to perform cutting off opera-
tions, a guard (24, Fig H) specic for this operation must be
tted. A suitable guard for cutting off operations part number
1004683-29 is available and can be obtained from Stanley Fat
Max service centres.
Fitting
u Place the tool on a table, with the spindle (11) facing up.
u Release the clamping lock (12) and hold the guard (5)
over the tool as shown.
u Align the lugs (13) with the notches (14).
u Press the guard down and rotate it counterclockwise to
the required position.
u Fasten the clamping lock (12) to secure the guard to the
tool.
u If required, tighten the screw (15) to increase the clamping
force.
Removing
u Release the clamping lock (12).
u Rotate the guard clockwise to align the lugs (13) with the
notches (14).
u Remove the guard from the tool.
Warning! Never use the tool without the guard.
Fitting the side handle
u Screw the side handle (3) into one of the mounting holes
in the tool.
Warning! Always use the side handle.
Fitting and removing grinding discs, cutting discs
or sanding ap pads (g. C - E)
Always use the correct type of disc for your application.
Always use discs with the correct diameter and bore size (see
technical data).
Fitting
u Fit the guard as described above.
u Place the inner ange (16) onto the spindle (11) as shown
(g. C). Make sure that the ange is correctly located on
the at sides of the spindle.
u Place the disc (17) onto the spindle (11) as shown (g.
C). If the disc has a raised centre (18), make sure that the
raised centre faces the inner ange.
u Make sure that the disc locates correctly on the inner
ange.
u Place the outer ange (19) onto the spindle. When tting
a grinding disc, the raised centre on the outer ange must
face towards the disc (A in g. D). When tting a cutting
disc, the raised centre on the outer ange must face away
from the disc (B in g. D).
u Keep the spindle lock (4) depressed and tighten the outer
ange using the two-pin spanner (8) (g. E).
Removing
u Keep the spindle lock (4) depressed and loosen the outer
ange (19) using the two-pin spanner (8) (g. D).
u Remove the outer ange (19) and the disc (17).
Fitting and removing sanding backing pads (g. E
& F)
For sanding, a backing pad is required. The backing pad is
available from your Stanley Fat Max dealer as an accessory.
Fitting
u Place the inner ange (16) onto the spindle (11) as shown
(g. F). Make sure that the ange is correctly located on
the at sides of the spindle.
u Place the backing pad (20) onto the spindle.
u Place the sanding disc (21) onto the backing pad.
u Place the outer sanding ange (22) onto the spindle with
the raised centre facing towards the disc.
u Keep the spindle lock (4) depressed and tighten the outer
ange using the two-pin spanner (8) (g. E). Make sure
that the outer ange is tted correctly and that the disc is
clamped tightly.
Removing
u Keep the spindle lock (4) depressed and loosen the outer
ange (19) using the two-pin spanner (8) (g. E).
u Remove the outer ange (19), the sanding disc (21) and
the backing pad (20).
9


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Stanley FMC761 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Stanley FMC761 in the language / languages: All languages as an attachment in your email.

The manual is 19,4 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info