Manual Stanley FMC650 (page 7 of 96) (English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish)

622182

Zoom out

Zoom in

1/96

ENGLISH

(Original instructions)

Assembly

Warning! Before assembly, remove the battery from the tool

and make sure that the saw blade has stopped. Used saw

blades may be hot.

Fitting and removing the saw blade (g. B)

u Hold the saw blade (10) with the teeth facing forward.

u Lift the saw blade locking lever (3) upwards.

u Insert the shank of the blade fully into the blade clamp (4)

as far as it will go.

u Release the lever.

u To remove the saw blade (10), lift the saw blade locking

lever (3) upwards and pull the blade out.

Fitting and removing the battery (g. C)

u To t the battery (7), line it up with the receptacle on the

tool. Slide the battery into the receptacle and push until

the battery snaps into place.

u To remove the battery, push the release buttons (11) while

at the same time pulling the battery out of the receptacle.

Use

Warning! Let the tool work at its own pace. Do not overload.

Warning! Never use the tool when the saw shoe is loose or

removed.

Charging the battery (g. A)

The battery needs to be charged before rst use and whenev-

er it fails to produce sufcient power on jobs that were easily

done before. The battery may become warm while charging;

this is normal and does not indicate a problem.

Warning! Do not charge the battery at ambient temperatures

below 10 °C or above 40 °C. Recommended charging tem-

perature: approx. 24 °C.

Note: The charger will not charge a battery if the cell

temperature is below approximately 10 °C or above 40 °C.

The battery should be left in the charger and the charger

will begin to charge automatically when the cell tempera-

ture warms up or cools down.

u To charge the battery (7), insert it into the charger (8).

The battery will only t into the charger in one way. Do

not force. Be sure that the battery is fully seated in the

charger.

u Plug in the charger and switch on at the mains.

The charging indicator (9) will blink.

The charge is complete when the charging indicator (9)

switches to continuously on. The charger and the battery can

be left connected indenitely. The LED will switch on as the

charger occasionally tops up the battery charge.

u Charge discharged batteries within 1 week. Battery life will

be greatly diminished if stored in a discharged state.

Leaving the battery in the charger

The charger and battery pack can be left connected with the

LED glowing indenitely. The charger will keep the battery

pack fresh and fully charged.

Charger diagnostics

If the charger detects a weak or damaged battery, the

charging indicator (9) will ash red at a fast rate. Proceed as

follows:

u Re-insert the battery (7).

u If the charging indicators continues ashing red at a fast

rate, use a different battery to determine if the charging

process works properly.

u If the replaced battery charges correctly, the original

battery is defective and should be returned to a service

centre for recycling.

u If the new battery gives the same indication as the original

battery, take the charger to be tested at an authorised

services centre.

Note: It may take as long as 30 minutes to determine that

the battery is defective. If the battery is too hot or too

cold, the LED will alternately blink red, fast and slow, one

ash at each speed and repeat.

Switching on and off (g. D & E)

u To switch on, slide the lock off switch (2) to the left then

pull and hold the variable speed trigger switch (1).

u To switch off, release the trigger switch (1).

Warning! Do not switch the tool on or off while under load.

Warning! Always slide the lock off switch (2) to the right, the

locked position when the tool is not in use.

Variable speed control

The variable speed on/off switch offers a choice of speeds for

greatly improved cutting rates in various materials.

u The speed is determined by the amount the trigger switch

(1) is pulled.

Bevel cutting (g. F, G & H)

The shoe plate can be set to a left or right bevel angle of 45°.

To set the bevel angle:

u Loosen the shoe retaining bolt (12) with the hex key

provided to unlock the shoe plate (5).

u Slide the shoe plate (5) forward to release it from the 0°

detent.

u Rotate the shoe plate to the desired bevel angle (g. G).

u Slide the shoe plate backwards to engage the left or right

detent.

u Tighten the shoe retaining bolt (12) with the hex key

provided to lock the shoe plate (5) in the required position.

Note: The shoe can be beveled to the left or to the right and

has detents at 45°.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Stanley FMC650 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 7,21 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Stanley FMC650 Manual

Product: